Add Commands
25-3
address
<IP_name or address>
add snmp
trap_community
<name>
The
add snmp trap_community
<name> command adds to the list of
community name/IP address pairs that are allowed to receive SNMP traps. This
command also allows multiple management stations to use the same SNMP trap
community name. Entries are added to the SNMP Trap Community Address Pool
table. Use the
list snmp trap_communities
command to display a list of the
authorized users.
The following parameters can be configured for the
add snmp community
command.
address
<IP_address>
trap_community_pool
<name>
trap_validate_address
[use_address | use_pool]
The following table describes each of these parameters.You can display authorized
users with the
list snmp trap_communities
command.
add snmp
trap_community_pool
<name>addresses <ip
address list>
The
add snmp trap_community_pool
<name>
addresses
<ip address list>
command adds up to four or eight entries at a time (depending on the number of
characters each IP address occupies) to the SNMP Trap Community Address Pool
table. If IP addresses are in the single-digit form as
1.1.1.1
, eight entries can be
added with the single CLI command; if addresses are in triple-digit form such as
146.115.112.111
, four IP addresses can be added with the single CLI command.
The maximum size of the pool is 10 IP addresses.
Parameter
Description
<pool_name>
Pool name defining a group of SNMP management stations. The limit is
10
.
IP_name or
address
IP name or address of an SNMP management station in the pool. The limit
is
10
.
Parameter
Description
<name>
Group name defining who can receive SNMP traps.
address
IP address of the SNMP manager, in the form
nnn.nnn.nnn.nnn.
trap_community_pool
Name of the trap community pool.
trap_validate_address
When set to
use_address
(
default
), the
address
of the SNMP
trap community is used to validate the management station’s IP
address. When set to
use_pool
, the management station’s IP
address is validated against the list of IP addresses associated
with the
trap_community_pool
. Employing
use_pool
selects IP
addresses from the pool as destination addresses and does not
use the specified
address
parameter although a token address
must be entered for purposes of backward compatibility.
Summary of Contents for OfficeConnect 3C100XF
