manualshive.com logo in svg

3Com CoreBuilder 3500, Implementation Manual, Page: 338 / 592

Share
Download
3Com CoreBuilder 3500 Implementation Manual Download Page 338

338

C

HAPTER

 13: IP M

ULTICAST

 R

OUTING

Key Concepts

This section describes several terms and concepts related to IP multicast 
routing.

Traffic Movement

Application sources generate the majority of IP multicast packets, but 
group members and routers that are communicating (DVMRP and IGMP 
messages) to establish the delivery path also generate IP multicast 
packets. 

Traffic from application sources always travels in one direction — 

downstream

 from the source to group members. Using various protocols, 

network devices are responsible for determining where group members 
exist and coordinating a loop-free delivery path from the source to them.

Traffic that relates to the delivery path can travel both 

upstream

 and 

downstream

 — between routers and between routers and group 

members.

IP Multicast Groups

Users can join or leave an IP multicast group at any time. Users request 
and cancel membership through mechanisms built into their desktop 
application — perhaps visible to the user as 

Go

 and 

Quit

 buttons. There 

are no restrictions on the physical location or number of members in a 
group. A user may belong to one or more groups at any time. 

Source-Group Pairs

Each IP multicast transmission can be linked to a unique pairing of a 
source address and multicast group address (destination address). In 
addition, network devices form a unique delivery path for each 
source-group pair. Multicast routers and switches track information about 
each source-group pair — mainly, the location of group members — and 
dynamically adjust the delivery path to ensure that IP multicast packets 
are delivered only where they need to go. 

Summary of Contents for CoreBuilder 3500

















































































































































































































































































































































































































































































































































































































Reviews:

No comments