3Com CoreBuilder 3500 Page 137 Implementation Manual Download | Manualshive

Page: 137 / 592

background image

Frame Processing

137

Frame Processing

All frames that are received on a physical interface and not explicitly
directed to the system or discarded are delivered to the corresponding
bridge port. The bridge port either forwards each frame to another
bridge port or discards it.

The system can discard an incoming frame for the following reasons:

■

The destination station is on the same segment as the source station.

■

The receive bridge port is blocked.

■

There is a problem with the frame.

The physical interface does not deliver frames with errors to the bridge
port. Thus, the

rxFrames

fields in the Ethernet statistics display and

bridge statistics display often report different values — that is, the
latter value is lower because it does not count frames in error.

■

A user-defined packet filter indicated not to receive the frame.

A frame that is forwarded from a physical interface to a bridge port is
then transmitted to a physical interface unless it is discarded. The system
can discard a frame at this point for the following reasons:

■

The transmit bridge port is blocked.

■

The frame is too large for the corresponding physical interface.

■

A user-defined packet filter indicated not to forward the frame.

«
...
135
136
137
138
139
...
»

Summary of Contents for CoreBuilder 3500

















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CoreBuilder 3500

Brand: ABRIVO Pages: 20

Brand: AU Pages: 3

Brand: WM Systems Pages: 102

Brand: KDDI Pages: 63

Brand: M4 Pages: 22

Brand: Sony Ericsson Pages: 208

myTouch myTouch 3G

Brand: T-Mobile Pages: 113

Brand: FLY Pages: 56

Brand: OfficeServ Pages: 63

Brand: Energizer Pages: 403

Brand: Alcatel Pages: 41

Brand: LOBSTER Pages: 75

Brand: Haier Pages: 65

Brand: Nokia Pages: 201

Brand: Zte Pages: 53

Brand: PCD Pages: 53

Brand: LG Pages: 18

Brand: LG Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands