manualshive.com logo in svg

3Com 3CRWX120695A, Configuration Manual

The 3Com 3CRWX120695A is a cutting-edge networking device designed to enhance your online experience. To ensure proper setup, refer to the comprehensive Hardware Installation Manual. Download the manual for free from our website today, providing step-by-step instructions and boosting your product knowledge.

Share
Download
background image

Backing Up and Restoring the System

613

To back up the current configuration file named 

configuration

 and reset 

the WX switch to the factory default configuration, type the following 
commands:

WX1200# 

copy configuration tftp://10.1.1.1/backupcfg

success: sent 365 bytes in 0.401 seconds [ 910 bytes/sec]
WX1200# 

clear boot config

success: Reset boot config to factory defaults.
WX1200# 

reset system force

...... rebooting ......

The 

reset system force

 command reboots the switch. The 

force

 option 

immediately restarts the system and reboots. If you do not use the 

force

 

option, the command first compares the running configuration to the 
configuration file. If the files do not match, MSS does not restart the WX 
switch but instead displays a message advising you to either save the 
configuration changes or use the 

force

 option.

Backing Up and 
Restoring the 
System

MSS has commands that enable you to easily backup and restore WX 
system and user files:

backup system 

[

tftp:/

ip-addr

/

]

filename

 

[

all 

|

 critical

]

restore system 

[

tftp:/

ip-addr

/

]

filename

 

[

all 

|

 critical

] 

[

force

]

The 

backup

 command creates an archive in Unix 

tape archive

 (

tar

) 

format. 

The 

restore

 command unzips an archive created by the 

backup

 

command and copies the files from the archive onto the switch. If a file in 
the archive has a counterpart on the switch, the archive version of the file 
replaces the file on the switch. The 

restore

 command does not delete 

files that do not have counterparts in the archive. For example, the 
command does not completely replace the user files area. Instead, files in 
the archive are added to the user files area. A file in the user area is 
replaced only if the archive contains a file with the same name. 

You can create or unzip an archive located on a TFTP server or in the 
switch’s nonvolatile storage. If you specify a TFTP server as part of the 
filename with the 

backup

 command, the archive is copied directly to the 

TFTP server and not stored locally on the switch. 

Summary of Contents for 3CRWX120695A

























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3CRWX120695A

IEI Technology WSB-H610 User Manual preview
WSB-H610
Brand: IEI Technology Pages: 187
IEI Technology TANK-XM811 User Manual preview
TANK-XM811
Brand: IEI Technology Pages: 71
Paradox ZX32D Manual preview
ZX32D
Brand: Paradox Pages: 4
M86 Security R3000 Series Evaluation Manual preview
R3000 Series
Brand: M86 Security Pages: 46
ETAS FETK-S2.1 User Manual preview
FETK-S2.1
Brand: ETAS Pages: 69
bintec elmeg RM7000 Installation Manual preview
RM7000
Brand: bintec elmeg Pages: 33
MFJ MFJ-492 Manual preview
MFJ-492
Brand: MFJ Pages: 11
Abit G740A Installation Manual And User'S Manual preview
G740A
Brand: Abit Pages: 22
Hafele Suzie-Q 541.35.520 Mounting Instructions preview
Suzie-Q 541.35.520
Brand: Hafele Pages: 12
Paradyne FrameSaver DSL 9788 Router Installation Instructions Manual preview
FrameSaver DSL 9788 Router
Brand: Paradyne Pages: 28
Konica Minolta SRX-101A Operation Manual preview
SRX-101A
Brand: Konica Minolta Pages: 31
ZALMAN RESERATOR2 Installation And Operational Manual preview
RESERATOR2
Brand: ZALMAN Pages: 18
Procool SP480 Series Instructions preview
SP480 Series
Brand: Procool Pages: 2
Tenda DH301 User Manual preview
DH301
Brand: Tenda Pages: 120
Billion BiPAC 5200S RC Series User Manual preview
BiPAC 5200S RC Series
Brand: Billion Pages: 79
Black Box Secure Site Manager 16 Quick Start Manual preview
Secure Site Manager 16
Brand: Black Box Pages: 16
National Instruments PCI-6601 User Manual preview
PCI-6601
Brand: National Instruments Pages: 52
3Com NETBuilder SI Using Manual preview
NETBuilder SI
Brand: 3Com Pages: 212

Brands by name

Popular brands

Load more brands