3Com 3CRWX120695A Configuration Manual Download Page 238 | Manualshive

Page: 238 / 728

background image

238

C

HAPTER

10: C

ONFIGURING

MAP A

CCESS

P

OINTS

Data rate enforcement is useful if you want to completely prevent clients
from transmitting at disabled data rates. For example, you can disable
slower data rates so that clients transmitting at these rates do not
consume bandwidth on the channel at the expense of clients transmitting
at faster rates.

Data rate enforcement is disabled by default. To enable data rate
enforcement for a radio profile, use the following command:

set radio-profile

profile-name

rate-enforcement mode

{

enable

|

disable

}

For example, the following command enables data rate enforcement for
radio profile

rp1.

WX#

set radio-profile rp1 rate-enforcement mode enable

The following command sets a 802.11g mandatory rate for service profile

sp1

to 54 Mbps and disables rates 1.0 Mbps and 2.0 Mbps:

WX#

set service-profile sp1 transmit-rates 11g mandatory 54.0

disabled 1.0,2.0

The following command maps radio profile

rp1

to service profile

sp1

.

WX#

set radio-profile rp1 service-profile sp1

After these commands are entered, if a client transmitting with a data
rate of 1.0 Mbps or 2.0 Mbps attempts to associate with a MAP managed
by service profile

sp1

, that client is not allowed to associate with the

MAP.

Disabling Idle-Client Probing

By default, a MAP radio sends keepalive messages (idle-client probes)
every 10 seconds to each client that has an active session on the radio, to
verify that the client is still active. The probes are unicast null-data frames.
Normally, a client that is still active sends an Ack in reply to an idle-client
probe.

If a client does not send any data or respond to any idle-client probes
before the user idle timeout expires (see “Changing the User Idle
Timeout” on page 239), MSS changes the client’s session to the
Disassociated state.

«
...
236
237
238
239
240
...
»

Summary of Contents for 3CRWX120695A

























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3CRWX120695A

Brand: IBM Pages: 86

IntelliJack NJ200

Brand: 3Com Pages: 4

Brand: 3xLogic Pages: 2

Brand: Danfoss Pages: 61

Brand: Analog Devices Pages: 76

Brand: insys icom Pages: 4

Brand: National Instruments Pages: 8

Brand: ZALMAN Pages: 7

Octopus G Series

Brand: TwinMOS Pages: 29

Brand: Medel Pages: 28

Brand: HighPoint Pages: 10

Brand: Rolls Pages: 1

Brand: Xenteq Pages: 16

Brand: Maxtor Pages: 2

Brand: AC Infinity Pages: 24

Brand: Alfa Network Pages: 11

Brand: Air Live Pages: 2

Brand: Extron electronics Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands