manualshive.com logo in svg

3Com 3CRWX120695A, Configuration Manual

The 3Com 3CRWX120695A is a cutting-edge networking device designed to enhance your online experience. To ensure proper setup, refer to the comprehensive Hardware Installation Manual. Download the manual for free from our website today, providing step-by-step instructions and boosting your product knowledge.

Share
Download
background image

516

C

HAPTER

 21: C

ONFIGURING

 AAA 

FOR

 N

ETWORK

 U

SERS

Combining EAP

Offload with

Pass-Through

Authentication

The following example illustrates how to enable PEAP-MS-CHAP-V2 
offload for the marketing (

mktg

) group and RADIUS pass-through 

authentication for members of engineering. This example assumes that 
engineering members are using DNS-style naming, such as is used with 
EAP-TLS. A WX server certificate is also required. 

1

Configure the RADIUS server 

r1

 at IP address 10.1.1.1 with the string 

starry 

for the key. Type the following command:

WX1200# 

set radius server r1 address 10.1.1.1 key starry

2

Configure the server group 

sg1

 with member 

r1

. Type the following 

command:

WX1200# 

set server group sg1 members r1

3

To authenticate all 802.1X users of SSID 

bobblehead

 in the group 

mktg

 

using PEAP on the WX switch and MS-CHAP-V2 on server 

sg1

, type the 

following command:

WX1200# 

set authentication dot1x ssid bobblehead mktg\* peap-mschapv2 sg1

4

To authenticate all 802.1X users of SSID 

aircorp

 in @eng.example.com via 

pass-through to 

sg1

, type the following command:

WX1200# 

set authentication dot1x ssid aircorp *@eng.example.com pass-through sg1

5

Save the configuration:

WX1200# 

save config

success: configuration saved.

Overriding

AAA-Assigned VLANs

The following example shows how to change the VLAN access of wireless 
users in an organization housed in multiple buildings. 

Suppose the wireless users on the faculty of a college English department 
have offices in building A and are authorized to use that building’s 

bldga-prof- 

VLANs. These users also teach classes in building B. Because 

you do not want to tunnel these users back to building A from building B 
when they use their wireless laptops in class, you configure the location 
policy on the WX switch to redirect them to the 

bldgb-eng

 VLAN. 

You also want to allow writing instructors normally authorized to use any 
-

techcomm

 VLAN in the college to access the network through the 

bldgb-eng

 VLAN when they are in building B. 

Summary of Contents for 3CRWX120695A

























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3CRWX120695A

Parker H Series Installation & Service Instructions Manual preview
H Series
Brand: Parker Pages: 344
Cambium Networks PTP 550 Series Quick Start Manual preview
PTP 550 Series
Brand: Cambium Networks Pages: 68
Cambium Networks PTP 820S Installation Manual preview
PTP 820S
Brand: Cambium Networks Pages: 110
Paradyne FrameSaver 9120 Installation Instruction Supplement preview
FrameSaver 9120
Brand: Paradyne Pages: 2
Ubiquiti ER-4 Quick Start Manuals preview
ER-4
Brand: Ubiquiti Pages: 22
Ublox NEO-D9S Quick Start Manual preview
NEO-D9S
Brand: Ublox Pages: 17
NetBurner MOD5272 Quick Start Manual preview
MOD5272
Brand: NetBurner Pages: 15
Sangamo CHOICE PR1 User Instructions preview
CHOICE PR1
Brand: Sangamo Pages: 2
Renesas H8/3864 Series User Manual preview
H8/3864 Series
Brand: Renesas Pages: 20
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Brand: C-Com Pages: 148
Patton electronics Model 2711 User Manual preview
Model 2711
Brand: Patton electronics Pages: 13
Angel Cool Aironet 1200 Quick Start Manual preview
Aironet 1200
Brand: Angel Cool Pages: 2
AirTies Air 4240 User Manual preview
Air 4240
Brand: AirTies Pages: 28
NETGEAR RH328 Reference Manual preview
RH328
Brand: NETGEAR Pages: 142
PaloAlto Networks ION 1000 Hardware Reference Manual preview
ION 1000
Brand: PaloAlto Networks Pages: 28
Variscite VAR-EXT-CB103 Manual preview
VAR-EXT-CB103
Brand: Variscite Pages: 17
City-Netek HomePNA PCI Adapter User Manual preview
HomePNA PCI Adapter
Brand: City-Netek Pages: 18
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Brand: Vivint Pages: 2

Brands by name

Popular brands

Load more brands