manualshive.com logo in svg

3Com 3CRWX120695A, Configuration Manual

The 3Com 3CRWX120695A is a cutting-edge networking device designed to enhance your online experience. To ensure proper setup, refer to the comprehensive Hardware Installation Manual. Download the manual for free from our website today, providing step-by-step instructions and boosting your product knowledge.

Share
Download
background image

Configuring 802.1X Authentication

453

„

host/*.nl.mycorp.com (userglob for the machine authentication rule)

„

*.nl.mycorp.com (userglob for the user authentication rule)

„

host/*.de.mycorp.com (userglob for the machine authentication rule)

„

*.de.mycorp.com (userglob for the user authentication rule)

Bonded Auth Period

The 

Bonded Auth period

 is the number of seconds MSS allows a Bonded 

Auth user to reauthenticate.

After successful machine authentication, a session for the machine 
appears in the session table in MSS. When the user logs on and is 
authenticated, the user session replaces the machine session in the table. 
However, since the user authentication rule contains the 

bonded

 option, 

MSS remembers that the machine was authenticated.

If a Bonded Auth user session is ended due to 802.1X reauthentication or 
the RADIUS Session-Timeout parameter, MSS can allow time for the user 
to reauthenticate. The amount of time that MSS allows for 
reauthentication is controlled by the Bonded Auth period. 

If the user does not reauthenticate within the Bonded Auth period, MSS 
deletes the information about the machine session. After the machine 
session information is deleted, the Bonded Auth user cannot 
reauthenticate. When this occurs, the user will need to log off, then log 
back on, to access the network. After multiple failed reauthentication 
attempts, the user might need to reboot the PC before logging on. 

By default, the Bonded Auth period is 0 seconds. MSS does not wait for a 
Bonded Auth user to reauthenticate. 

You can set the Bonded Auth period to a value up to 300 seconds. 3Com 
recommends that you try 60 seconds, and change the period to a longer 
value only if clients are unable to authenticate within 60 seconds.

To set the Bonded Auth period, use the following command:

set dot1x bonded-period 

seconds

To reset the Bonded Auth period to its default value (0), use the following 
command:

clear dot1x bonded-period

Summary of Contents for 3CRWX120695A

























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3CRWX120695A

NEC Univerge SV8100 System Configuration Manual preview
Univerge SV8100
Brand: NEC Pages: 44
Magnat Audio MC 200 Faq preview
MC 200
Brand: Magnat Audio Pages: 2
Ubiquiti airFiber AF-5X User Manual preview
airFiber AF-5X
Brand: Ubiquiti Pages: 50
H3C S5120V3-EI Series Manual preview
S5120V3-EI Series
Brand: H3C Pages: 54
Ublox LENA-R8 Series System Integration Manual preview
LENA-R8 Series
Brand: Ublox Pages: 116
H3C CR16000-M Installation Manual preview
CR16000-M
Brand: H3C Pages: 116
AlphaShield INTERNET PRIVACY PROTECTION (Spanish) Manual Del Usuario preview
INTERNET PRIVACY PROTECTION
Brand: AlphaShield Pages: 49
Grasslin TOWERCHRON DP72 Programming Manual preview
TOWERCHRON DP72
Brand: Grasslin Pages: 2
Maxim DS5001FP Specification Sheet preview
DS5001FP
Brand: Maxim Pages: 26
NetComm 3GM1WN Quick Start Manual preview
3GM1WN
Brand: NetComm Pages: 3
Ensemble Designs Avenue Express Control Panel Data Pack preview
Avenue Express Control Panel
Brand: Ensemble Designs Pages: 19
APARIAN DH485 Quick Start Manuals preview
DH485
Brand: APARIAN Pages: 2
axing EOC 1-31 Operation Instructions Manual preview
EOC 1-31
Brand: axing Pages: 52
Dialogic Media Board D/120JCT-LS-EW Installation Manual preview
Media Board D/120JCT-LS-EW
Brand: Dialogic Pages: 2
1&1 Homeserver+ Quick Start Manual preview
Homeserver+
Brand: 1&1 Pages: 32
Sparklan WNFB-265AXI(BT) User Manual preview
WNFB-265AXI(BT)
Brand: Sparklan Pages: 14
Ethernet Direct Husky HMG-1648EP User Manual preview
Husky HMG-1648EP
Brand: Ethernet Direct Pages: 16
Hama 00176547 Operating Instruction preview
00176547
Brand: Hama Pages: 25

Brands by name

Popular brands

Load more brands