IES4005M User’s Guide
143
C
H A P T E R
1 9
IPv6
Use these commands to configure IPv6 settings.
IPv6 (Internet Protocol version 6), is designed to enhance IP address size and features. The
increase in IPv6 address size to 128 bits (from the 32-bit IPv4 address) allows up to 3.4 x 10
38
IP
addresses.
The 128-bit IPv6 address is written as eight 16-bit hexadecimal blocks separated by colons (:). This
is an example IPv6 address
2001:0db8:1a2b:0015:0000:0000:1a2f:0000
.
IPv6 addresses can be abbreviated in two ways:
• Leading zeros in a block can be omitted. So
2001:0db8:1a2b:0015:0000:0000:1a2f:0000
can
be written as
2001:db8:1a2b:15:0:0:1a2f:0
.
• Any number of consecutive blocks of zeros can be replaced by a double colon. A double colon can
only appear once in an IPv6 address. So
2001:0db8:0000:0000:1a2f:0000:0000:0015
can be
written as
2001:0db8::1a2f:0000:0000:0015
,
2001:0db8:0000:0000:1a2f::0015
,
2001:db8::1a2f:0:0:15
or
2001:db8:0:0:1a2f::15.
IPv6 Prefix and Prefix Length
Similar to an IPv4 subnet mask, IPv6 uses an address prefix to represent the network address. An
IPv6 prefix length specifies how many most significant bits (start from the left) in the address
compose the network address. The prefix length is written as “/x” where x is a number. For
example,
2001:db8:1a2b:15::1a2f:0/32
means that the first 32 bits (
2001:db8
) is the subnet prefix.
IPv6 Subnet Masking
Both an IPv6 address and IPv6 subnet mask compose of 128-bit binary digits, which are divided
into eight 16-bit blocks and written in hexadecimal notation. Hexadecimal uses four bits for each
character (1 ~ 10, A ~ F). Each block's 16 bits are then represented by four hexadecimal
characters. For example, FFFF:FFFF:FFFF:FFFF:FC00:0000:0000:0000.
The first 48 bits of the IPv6 subnet mask are for Internet routing or fixed for local address, the 49th
to the 64th bits are for subnetting and the last 64 bits are for interface identifying. The 16 binary
digits for subnetting allows an organization to set up to 65,535 individual subnets.
Interface ID
In IPv6, an interface ID is a 64-bit identifier. It identifies a physical interface (for example, an
Ethernet port) or a virtual interface (for example, the management IP address for a VLAN). One
interface should have a unique interface ID.
Содержание IES4005M
