ZURN PEX Скачать руководство пользователя страница 11

Страница: 11 / 40

Page 10

Zurn PEX

Plumbing Installation Guide

ZURN PEX, INC.

HIGHWAY 11 EAST, COMMERCE, TEXAS, U.S.A. 75428 • PHONE: 855-ONE-ZURN (855-663-9876) • FAX: 903-886-2583 • www.zurn.com

QickClamp

System

•  Patent-pending technology
•  One tool system
•   Available in 3/8", 1/2", 3/4", and 1" sizes
•  Go Gauge
•  25-year system warranty

Crimp Systems

Zurn offers three different clamp fitting systems: the QickClamp, the Copper Crimp Ring, and the Stainless Steel Clamp Ring

system. To choose the clamp system most appropriate for your installation, consider factors relative to your jobsite priorities.

Listings

By NSF International as meeting the following standards:
  ASTM F877
  CAN/CSA B137.5
  NSF Standard 14

Important:

The QickClamp cannot be used with Zurn PEX transi-

tional fittings which are used to transition from polybutylene to PEX.

Making The Connection with the Medium QickClamp Tool

Important:

Using this tool for anything other than its intended purpose voids the warranty.

1) Measure and cut the tube. Be sure you have a square,

burr-free cut. An uneven or jagged cut may cause an
improper connection.

2) Push tubing into the QickClamp until the tubing stops at

locating fingers.

Do not force the tubing to bottom out in

the QickClamp.

Some tubing should be visible in the sight

hole.

Be sure that the tab inside the QickClamp stays on

the outside of the tubing.

3) Push fitting into the tubing until the fitting shoulder touches the

locating fingers on the QickClamp.

4) Open the QickClamp Medium Crimp Tool* and pull the middle

handle down. Hold the tool in one hand with your thumb over
the middle handle and your fingers around the bottom handle.
Place the jaws completely over the QickClamp pinch ear.

Important:

Be sure the tool jaws cover the entire ear of the

QickClamp before crimping; failure to do so will result in an
improper crimp and may void the warranty.

QickClamp rings must not come in contact with solder flux.

Содержание PEX









































Результаты поиска

Содержание PEX

Отзывы:

Похожие инструкции для PEX

Бренды по названию

Популярные бренды

ZURN PEX, Руководство по установке

Результаты поиска

Содержание PEX

Отзывы:

Похожие инструкции для PEX

Бренды по названию

Популярные бренды