ZURN PEX Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 40

background image

Page 16

Zurn PEX

®

Plumbing Installation Guide

ZURN PEX, INC.

HIGHWAY 11 EAST, COMMERCE, TEXAS, U.S.A. 75428 • PHONE: 855-ONE-ZURN (855-663-9876) • FAX: 903-886-2583 • www.zurn.com

Adjusting the Medium Crimp Tool

Note:

Zurn Crimp Tools are factory set to provide proper crimps.

This should be checked before use by making a test crimp
connection and checking it with the crimp gauge. As long as
the finished crimp connection gauges properly, there is no need
to adjust the tool.
All crimp tools wear, which increases the crimp diameter after
many crimps. When the crimps start to approach the maximum
ring diameter, adjust the back pin. To adjust for a tighter crimp,
remove the E-clip (for example, pop it off with a screw driver)
and slide the back pin head out about 1/4 inch.

Warning: The

Adjustment Pin must not be pulled or pushed completely out.

Rotate the back pin until the line on the hex head points to the
next highest number on the tool body, push the pin back in, and
refit the E-clip. Five adjustments are available.

For a tighter crimp, turn mark on pin to the next number:

0

1

2

3

4

5

Maintenance

For easier, better crimps and longer tool life, keep tool clean and
rust-free inside and out. Lubricate all moving parts frequently with
light oil.

«
...
15
16
17
18
19
...
»

Содержание PEX









































Отзывы:

Нет отзывов

Похожие инструкции для PEX

Бренд: Zetec Страницы: 23

Litmann Quality 3100

Бренд: 3M Страницы: 2

Бренд: IBS Scherer Страницы: 64

Tablet1000 Series

Бренд: Hantek Страницы: 98

Бренд: Qlight Страницы: 4

Бренд: Quantum Страницы: 11

Бренд: Quanser Страницы: 21

Бренд: YASKAWA Страницы: 52

Бренд: Life Fitness Страницы: 8

Бренд: Moticon Страницы: 24

Бренд: Interacoustics Страницы: 2

Бренд: Xpression Страницы: 4

Бренд: M-Audio Страницы: 4

STIMPOD NMS 410

Бренд: Xavant Страницы: 36

Lumify USB Solar Fairy Lights

Бренд: solarcentre Страницы: 2

Бренд: R.V.R. Electronica Страницы: 60

Dirt Doctor Junior

Бренд: Newstripe Страницы: 8

Бренд: Cropter Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды