ZURN PEX Скачать руководство пользователя страница 36

Страница: 36 / 40

Page 35

ZURN PEX, INC.

HIGHWAY 11 EAST, COMMERCE, TEXAS, U.S.A. 75428 • PHONE: 855-ONE-ZURN (855-663-9876) • FAX: 903-886-2583 • www.zurn.com

Zurn PEX

Plumbing Installation Guide

ZURN PEX, INC.

HIGHWAY 11 EAST

COMMERCE, TX

PHONE: 855-ONE-ZURN (855-663-9876)

FAX: 903/886-2583
In Canada:

ZURN INDUSTRIES LIMITED

3544 NASHUA DRIVE

MISSISSAUGA, ONTARIO CANADA L4V 1L2

PHONE: 905/405-8272

FAX: 905/405-1292
www.zurn.com

ZMKTG370-16, Rev. 3/13

This is to certify that the person named on this
card has received instruction and successfully
completed an examination on the proper
installation of Zurn PEX XL brass, Zurn PEX CR,
and QickClamp

™

insert and crimp fittings, Zurn

crimp tools, Zurn gauges, and Zurn PEX tubing.

ZMKTG370-16 Pex Cert-MAR13-hi_QestPex Certification/QPX20 3/18/13 4:43 PM Page 32

Listings

NSF International

Zurn PEX oxygen barrier and non-barrier tubing, Zurn PEX XL fittings, Zurn PEX

CR, QickClamp

™

, Qicktite

fittings, Zurn PEX

supply tubes.

International Association of Plumbing & Mechanical Officials (IAPMO)

Zurn PEX oxygen barrier and non-barrier tubing, Zurn PEX XL fittings,

Zurn PEX supply tubes, Waterflex

water heater connectors.

Model Codes

The following model codes recognize Crosslinked Polyethylene (PEX) tubing

for use in hot and cold water distribution systems:

IPC – International Plumbing Code

(ICC)

IRC – International Residential Code

(ICC)

National Standard Plumbing Code

(NAPHCC)

UPC – Uniform Plumbing Code

(IAPMO)

U.S. Department of Housing and Urban Development

(HUD)

The following model codes recognize Crosslinked Polyethylene (PEX) tubing

for use in radiant heating systems:

UMC – IAPMO Uniform Mechanical Code

(IAPMO)

IMC – International Mechanical Code

(ICC)

It is the responsibility of the installer to ensure that these products

are accepted by local code authorities before installing the product.

Содержание PEX









































Результаты поиска

Содержание PEX

Отзывы:

Похожие инструкции для PEX

Бренды по названию

Популярные бренды

ZURN PEX, Руководство по установке

Результаты поиска

Содержание PEX

Отзывы:

Похожие инструкции для PEX

Бренды по названию

Популярные бренды