Zoom GFX-8, Руководство по эксплуатации

Страница: 28 / 46

Effects
a
nd
Parameters
28
ZOOM GFX-8
LED lit: TRM RATE parameter is at maximum.
LED out: TRM RATE parameter is at the value stored for
that patch.
This is a reverb effect for which the envelope (sound change curve) can
be adjusted.
Adjusts the reverb time.
Adjusts the reverb sound envelope.
Adjusts the effect sound mix ratio. A value of 50 results in only
the effect sound being output.
See TYPE 1A (REV HALL) .
If the effect is ON and the CONTROL switch is operated,
the effect will be bypassed while the switch is pushed.
This is a pitch shifter that allows changing the pitch according to the
key of the song.
Selects the keynote of the scale.
Sets the harmonic interval from the keynote.
M3 = major third m3 = minor third
4t = complete fourth 5t = complete fifth
6t = major sixth
Adjusts the pitch shift direction. "dn" means downward shift, and
"UP" upward shift.
See TYPE 1A (REV HALL) .
If the effect is ON and the CONTROL switch is operated,
the effect will be bypassed while the switch is pushed.
This effect uses two pitch shifters.
Sets the pitch of pitch shift 1 in semitones.
Sets the pitch of pitch shift 2 in semitones.
Selects monaural (Mn) or stereo (St) operation.
Adjusts the effect sound level.
See
TYPE 1A (REV HALL)
.
If the effect is ON and the CONTROL switch is operated,
the effect will be bypassed while the switch is pushed.
This is a sample & hold effect with automatic picking synchronization.
Selects the effect pattern.
Select a suitable setting to match the guitar.
Adjusts the level of the original sound.
Adjusts the effect sound level.
See
TYPE 1A (REV HALL)
.
If the effect is ON and the CONTROL switch is operated,
the effect will be bypassed while the switch is pushed.
This is an effect that creates a synthesizer type sound.
Selects the synthesizer sound character.
Adjusts the level of the original sound.
Adjusts the level of the synthesizer sound.
See
TYPE 1A (REV HALL)
.
If the effect is ON and the CONTROL switch is operated,
the effect will be bypassed while the switch is pushed.
Call up the previously stored custom settings 1/2 for the MOD module.
(For information on creating and storing custom settings, see page 18.)
The currently stored parameters can be edited. To retain any changes,
store the patch.
CUSTOM2 11B TYPE
CUSTOM1 11A TYPE
Parameter 8 Parameter 5
0 - 50
WET LVL
Parameter 4
0 - 50
DRY LVL
Parameter 3
1 - 20
SENS
Parameter 2
1 - 5
COLOR
Parameter 1
SYNTH 10B TYPE
Parameter 8 Parameter 5
0 - 50
WET LVL
Parameter 4
0 - 50
DRY LVL
Parameter 3
1 - 20
SENS
Parameter 2
1 - 10
PATTERN
Parameter 1
SMPLHOLD 10A TYPE
Parameter 8 Parameter 5
0 - 50
BALANCE
Parameter 4
Mn/St
MODE Parameter 3
-12 - -1, oF, 1 - 12, 24
PITCH 2 Parameter 2
-12 - -1, oF, 1 - 12, 24
PITCH 1 Parameter 1
TWIN PIT 9B TYPE
Parameter 8 Parameter 5
0 - 50
HPS MIX Parameter 4
dn, UP
SHIFT Parameter 3
M3, m3, 4t, 5t, 6t
SCALE Parameter 2
C, C#, --- A#, b
KEY Parameter 1
HPS 9A TYPE
Parameter 8 Parameter 5
0 - 50
GATE MIX Parameter 4
Envelope
0
10 -10
-10 - 0 - 10
ENV Parameter 3
0 - 50
PRE DLY Parameter 2
1 - 30
DECAY Parameter 1
GATE REV 8B TYPE