Effects
a
nd
Parameters
25
ZOOM GFX-8
DLY/REV (Delay/Reverb) module
This module contains mainly single reverb type effects such as delay and reverb, but it also covers combinations with
modulation effects and special effects and contains the jam effect making use of sampling technology.
Common Parameters of DLY/REV Module
Adjusts the modulation rate.
Adjusts the effect mix ratio.
Adjusts the balance between effect sound
and original sound. Higher values result in
more pronounced effect sound.
Adjusts the amount of feedback.
Adjusts the effect operation direction. "dn"
means downward change, and "UP" upward
change.
* TYPE 1A and 1B have the same parameters.
This is a reverb effect simulating concert hall reverb.
This is a reverb effect simulating room reverb.
Adjusts the reverb duration (reverb time).
Adjusts the predelay time from the onset of the original sound
until the start of reverb.
Adjusts the tone of the effect sound.
Using the maximum value of the parameter adjusted by RTM as
reference (100%), this parameter adjusts the RTM maximum
value in the range from 0% (0) - 100% (1.0).
Using the maximum value of the parameter adjusted by RTM as
reference (100%), this parameter adjusts the RTM minimum
value in the range from 0% (0) - 100% (1.0).
Selects the parameter to be adjusted by RTM. Parameter 1 - 4 can
be selected.
Selects the controller to use for RTM. Available settings are "oF"
(off), "Pd" (expression pedal), MIDI control change 1 - 5, 8 - 31.
If the effect is ON and the CONTROL switch is operated,
the effect will be bypassed while the switch is pushed.
* TYPE 2A and 2B have the same parameters.
This is a combination of delay and hall reverb.
This is a combination of delay and room reverb.
Sets the delay time in 10-ms units (10 ms x setting value = delay
time).
Adjusts the amount of delay feedback.
Adjusts the delay sound mix ratio.
Adjusts the reverb sound mix ratio.
See
TYPE 1A (REV HALL)
.
Sets the delay time according to the interval in which the
CONTROL switch is operated.
This is a ping-pong type delay where the sound is alternately panned
right and left. The delay time of 1 millisecond to 6 seconds.
Sets delay time in 100-ms units.
Sets delay time in 1-ms units.
See
TYPE 1A (REV HALL)
.
Sets the delay time according to the interval in which the
CONTROL switch is operated.
This is an effect where the delay sound continues to be heard for up to 3
seconds after the patch is switched.
* To use the seamless effect, the seamless delay must be
selected at the newly called up patch.
Sets the delay time. In the range from 1 - 99, the formula is 10
ms x setting value = delay time. In the range from 1.0 - 6.0 (for
3B SEAMLESS, the maximum is 3.0), the formula is 1000 ms x
setting value = delay time. When the PARM 1 knob is moved,
the value changes in steps of 5. For fine adjustment, use the
PARM VALUE knob.
Adjusts the duration for which the delay sound is heard after the
patch was switched (100 ms x setting value = remain duration).
The setting "Hd" means that the delay sound remains for the time
set for that patch.
1 - 99, 1.0, Hd
SEAMTIME
Parameter 2
1 - 99, 1.0 - 3.0
TIME
Parameter 1
SEAMLESS
3B
TYPE
Parameter 8
Parameter 5
0 - 50
PPD MIX
Parameter 4
0 - 50
FEEDBACK
Parameter 3
0 - 99
TIMEx1
Parameter 2
0 - 60
TIMEx100
Parameter 1
PP DLY
3A
TYPE
Parameter 8
Parameter 5
0 - 50
(when 2B is selected)
ROOM MIX
Parameter 4
0 - 50
(when 2A is selected)
HALL MIX
Parameter 4
0 - 50
DLY MIX
Parameter 3
0 - 50
DLY FB
Parameter 2
1 - 99, 1.0
DLY TIME
Parameter 1
DLY+ROOM
2B
TYPE
DLY+HALL
2A
TYPE
oF
,
Pd
,
1 - 5
,
8 - 31
RTM CTL
Parameter 8
1 - 4
RTM DES
Parameter 7
0 - 99
,
1.0
RTM MIN
Parameter 6
0 - 99
,
1.0
RTM MAX
Parameter 5
0 - 50
(when 1B is selected)
ROOM MIX
Parameter 4
0 - 50
(when 1A is selected)
HALL MIX
Parameter 4
0 - 10
TONE
Parameter 3
0 - 50
PRE DLY
Parameter 2
1 - 30
TIME
Parameter 1
REV ROOM
1B
TYPE
REV HALL
1A
TYPE
SHIFT
FEEDBACK
BALANCE
xx MIX
RATE
Indicates a parameter for
which tap input is possible
with the CONTROL switch
(see page 31).
[CONTROL SW]
indicates an
item that can be operated with
the CONTROL switch (see page
31).
Indicates a parameter
that can be controlled by
RTM (see page 30).
Indicates a parameter that can
be controlled with the PARM
VALUE knob during easy edit
(see page 11).
