with the ZNR/EQ EDIT key. (If the PARM SELECT knob is used,
parameters 1 - 12 can be called up continuously.)
Adjusts boost/cut in the ultra-high range (above 8 kHz).
Adjusts boost/cut in the high range.
Adjusts boost/cut in the midrange.
Adjusts boost/cut in the low range.
(Equalizer Page 2)
This is page 2 of the four-band equalizer.
Adjusts the level of the signal after passing the EQ module. A
setting of 25 gives unity level (input level = output level).
Adjusts the center frequency in the high range (630 Hz - 6.3
kHz).
Adjusts the center frequency in the midrange (160 Hz - 1.6 kHz).
Adjusts the center frequency in the low range (60 Hz - 630 Hz).
EQ module setting values and frequencies
Using the maximum value of the parameter adjusted by RTM as
reference (100%), this parameter adjusts the RTM maximum
value in the range from 0% (0) - 100% (1.0).
Using the maximum value of the parameter adjusted by RTM as
reference (100%), this parameter adjusts the RTM minimum
value in the range from 0% (0) - 100% (1.0).
Selects the parameter to be adjusted by RTM. Parameter 1 - 8 can
be selected.
Selects the controller to use for RTM. Available settings are "oF"
(off), "Pd" (expression pedal), MIDI control change 1 - 5, 8 - 31.
When the effect is ON, the output is muted while the
CONTROL switch is pressed (during muting, the LED
lights up).
oF
,
Pd
,
1 - 5
,
8 - 31
RTM CTL
Parameter 8
1 - 8
RTM DES
Parameter 7
0 - 99
,
1.0
RTM MIN
Parameter 6
0 - 99
,
1.0
RTM MAX
Parameter 5
BASS FRQ
Display
60Hz
06
80Hz
08
125Hz
12
160Hz
16
200Hz
20
315Hz
31
400Hz
40
630Hz
63
MID FRQ
Display
160Hz
16
200Hz
20
315Hz
31
400Hz
40
630Hz
63
800Hz
80
1.2kHz
1.2
1.6kHz
1.6
TREBLE FRQ
Display
630Hz
63
800Hz
80
1.2kHz
1.2
1.6kHz
1.6
2.5kHz
2.5
3.2kHz
3.2
5.1kHz
5.1
6.3kHz
6.3
06 - 63 (see table)
BASS FRQ
Parameter 4
16 - 1.6 (see table)
MID FRQ
Parameter 3
63 - 6.3 (see table)
TRBL FRQ
Parameter 2
1 - 30
EQ LEVEL
Parameter 1
P2
EQ
-12 - 12
BASS
Parameter 4
-12 - 12
MIDDLE
Parameter 3
-12 - 12
TREBLE
Parameter 2
-12 - 12
PRESENCE
Parameter 1
21
ZOOM GFX-8
Effects
a
nd
Parameters
This module contains spatial effects such as chorus and flanger, unique sounding effects such as auto-wah, and modulation effects
such as ring modulator.
Common Parameters of MOD Module
Adjusts the effect depth.
Adjusts the modulation rate.
Adjusts the predelay time.
Adjusts the effect mix ratio.
Adjusts the balance between effect sound
and original sound. Higher values result in
more pronounced effect sound.
Adjusts the amount of feedback.
Adjusts the effect operation direction. "dn"
means downward change, and "UP" upward
change.
Adjusts the picking detection sensitivity for
wah and the trigger sensitivity.
Selects the MOD module connection point.
bF: Before DRIVE module AF: After EQ
module
This is a chorus effect with clear sound.
Using the maximum value of the parameter adjusted by RTM as
reference (100%), this parameter adjusts the RTM maximum
value in the range from 0% (0) - 100% (1.0).
Using the maximum value of the parameter adjusted by RTM as
reference (100%), this parameter adjusts the RTM minimum
value in the range from 0% (0) - 100% (1.0).
Selects the parameter to be adjusted by RTM. Parameter 1 - 4 can
be selected.
Selects the controller to use for RTM. Available settings are "oF"
(off), "Pd" (expression pedal), MIDI control change 1 - 5, 8 - 31.
LED lit: CHO MIX parameter is at maximum.
LED out: CHO MIX parameter is at the value stored for that
patch.
This is a chorus effect characterized by warm sound.
Adjusts the sound quality.
0 - 50
TONE
Parameter 3
1 - 50
RATE
Parameter 2
0 - 50
DEPTH
Parameter 1
CE CHO
1B
TYPE
oF
,
Pd
,
1 - 5
,
8 - 31
RTM CTL
Parameter 8
1 - 4
RTM DES
Parameter 7
0 - 99
,
1.0
RTM MIN
Parameter 6
0 - 99
,
1.0
RTM MAX
Parameter 5
0 - 50
CHO MIX
Parameter 4
0 - 50
PRE DLY
Parameter 3
1 - 50
RATE
Parameter 2
0 - 50
DEPTH
Parameter 1
CHORUS
1A
TYPE
POSITION
SENS
SHIFT
FEEDBACK
BALANCE
xx MIX
PRE DLY
RATE
DEPTH
Indicates a parameter for
which tap input is possible
with the CONTROL switch
(see page 31).
[CONTROL SW]
indicates an
item that can be operated with
the CONTROL switch (see
page 31).
Indicates a parameter
that can be controlled by
RTM (see page 30).
Indicates a parameter that can
be controlled with the PARM
SELECT knob during easy edit
(see page 11).
MOD (Modulation) Module
