Zoom g9.2tt, Руководство по эксплуатации

Страница: 31 / 51

ZOOM G9.2tt
60
This effect simulates a tape echo.
The above two effect types have the same parameters.
PARM1 PARM2 PARM3 PARM4
Time
1 –
2000
mS
FeedBack
0 – 100
HiDamp
0 – 10
Mix
0 – 100
Sets the delay time.
Adjusts the amount of feedback.
Higher setting values result in a
higher number of delay sound Adjusts the treble attenuation
of the delay sound. Lower
setting values result in softer
Adjusts the level of the effect
sound mixed to the original
DELAY module
This is a delay module that allows use of the hold function.
Delay
This is a long delay with a maximum setting of 5000 ms.
WAH/EFX1 module
This module comprises wah and filter effects as well as special effects such as ring
modulator and octave.
AutoWah
This effect varies wah in accordance with picking intensity.
A-Resonance
This effect varies the resonance filter frequency in accordance with picking intensity.
The above two effect types have the same parameters.
PARM1 PARM2 PARM3 PARM4
Position
Befr, Aftr
Sense
-10 – -1,
1 – 10
Resonance
0 – 10
Level
2 – 100
Effect parameters 1 – 4
Effect type
When this effect type is selected, the four parameters listed
here can be adjusted with parameter knobs 1 - 4. The setting
range for each parameter is also shown. Some effect
parameters are adjusted with the knobs of the pre-amp section.
Tempo sync
The note symbol ( ) in the table indicates that the parameter can be synchronized to the
patch specific tempo. If you select the note symbol as value for the parameter when making the
setting at the G9.2tt, the parameter value will be synchronized to the patch specific tempo in
note units ( → p. 39).
Expression pedal
The pedal symbol ( ) in the table indicates that the parameter can be controlled with the
expression pedal 1/2. If you select the parameter as control target when making the setting at
the G9.2tt ( → p. 32 – 35), the expression pedal 1/2 will adjust the parameter in real time when
the patch is selected. Parameters with the pedal symbol can also be selected as control targets
for the ARRM function.
Delay tap/hold delay/delay mute
The tap ( ), hold ( ), and mute ( ) symbols in the table indicate that the
respective function foot switch 1/2 can be used to specify the delay time (TAP), toggle hold
delay on and off (HOLD), or toggle mute between on and off (MUTE). These functions apply only
to the DELAY module.
To use these functions, the respective function must be assigned to the function foot switch 1/2
( → p. 38) and the respective effect type must be enabled.
Effect module
Effect Types and Parameters
How to read the parameter table
Effect Types and Parameters
ZOOM G9.2tt
61
COMP module
Attenuates high-level signal components and boosts low-level signal components, to keep
the overall signal level within a certain range.
Compressor
This is an MXR Dynacomp type compressor.
PARM1 PARM2 PARM3 PARM4
Sense
0 – 10
Attack
Fast, Slow
Tone
0 – 10
Level
2 – 100
Adjusts the compressor
sensitivity. Higher setting
values result in higher
sensitivity.
Selects compressor attack
speed in two levels: Fast or
Slow.
Adjusts the tonal quality of the
sound. Adjusts the signal level after
passing the module.
RackComp
This effect type allows more detailed adjustment than "Compressor".
PARM1 PARM2 PARM3 PARM4
Threshold
0 – 50
Ratio
1 – 10
Attack
1 – 10
Level
2 – 100
Adjusts the reference signal
level for the compressor
action.
Adjusts the compression ratio.
Adjusts the compressor attack
speed. Adjusts the signal level after
passing the module.
Limiter
This is a limiter that suppresses signal peaks above a certain reference level.
PARM1 PARM2 PARM3 PARM4
Threshold
0 – 50
Ratio
1 – 10
Release
1 – 10
Level
2 – 100
Adjusts the reference signal
level for the limiter action. Adjusts the compression ratio
of the limiter.
Adjusts the delay between the
point where the signal level
falls below the threshold level
and the limiter release.
Adjusts the signal level after
passing the module.
WAH/EFX1 module
This module comprises wah and filter effects as well as special effects such as ring
modulator and octave.
AutoWah
This effect varies wah in accordance with picking intensity.
See A-Resonance (next effect) for effect parameters.
A-Resonance
This effect varies the resonance filter frequency in accordance with picking intensity.
PARM1 PARM2 PARM3 PARM4
Position
Befr, Aftr
Sense
-10 – -1,
1 – 10
Resonance
0 – 10
Level
2 – 100
Selects the connection
position of the WAH/EFX1
module. Available settings are
"Befr" (before pre-amp
section) or "Aftr" (after pre-
amp section).
Adjusts the effect sensitivity.
Adjusts the intensity of the
resonance sound. Adjusts the signal level after
passing the module.
Booster
This is a booster for increasing signal gain.
PARM1 PARM2 PARM3 PARM4
Range
1 – 5
Tone
0 – 10
Gain
0 – 10
Level
2 – 100
Adjusts the frequency range to
boost. Adjusts the tonal quality of the
sound.
Adjusts the amount of boost.
Adjusts the signal level after
passing the module.