background image

Ϯϯ

 

sϴ͘Ϯϭ

 

/ŶƐƚĂůůĂƟŽŶDĂŶƵĂů

 

 

WARRANTY

 

MADEL ATD guarantees all its products against production defects for a period of two (2) years. This period will start from the date of delivery of the goods 
to the DISTRIBUTOR. The warranty will only cover replacement of defective products, not including labour, travel, replacement of other damaged products, 
etc., or any other disbursement, expenses or consequential damages. The warranty will not cover the damage incurred in the products due  to  i incorrect 
installation,  h a n d l i n g   or  storage  in  p o o r   conditions. 

The procedure to follow in the case of return of the Madel ZONING system under warranty is as follows: If there is any problem, you should contact MADEL tech-
nical support service (902.550.290) who will try to solve any problems and answer any questions about the installation. It is important to call from the 
place where the equipment is installed in order to carry out the necessary tests to diagnose the equipment. If any anomaly is detected, returning the equip-
ment for factory inspection will be authorised. Our technical support will provide a written authorisation for the return of the equipment under warranty. 
This authorisation can only be completed by Madel technical staff and should be affixed to the equipment. It will also serve for monitoring its return, which 
should be made through your usual distributor. 

All returned equipment must be in perfect conditions of use and must have all the initial additional components, such as sensors, antenna, etc. 

Содержание Zity

























Отзывы: