background image

page 15

enGlisH

  

 

Installation and Operation Manual   

|

   Legacy™ Model LRZM Pool/Spa Heater 

LRZ Pressure Drop vs Flow

0

0.5

1

1.5

2

2.5

3

3.5

4

4.5

5

0

100

200

300

400

500

Water Flow (LPM)

 P

re

ss

ur

Dr

op

 (m

 H

2O

)

LRZ125

LRZ250

LRZ175

LRZ325

LRZ400

5.5 

reversible Water Connections

The Legacy Model LRZ millivolt heater is 

shipped with water connections on the right side, 

but can be modified in the field to provide left-side 

water connections. This procedure involves remov-

ing the heat exchanger headers and reinstalling them 

on opposite ends of the tube assembly. Some of the 

heater wiring must be disconnected and re-routed, so 

this procedure must be done only by a trained service 

technician. Heat exchanger reversals are generally 

done before the installation of power and water to the 

heater. If you need to reverse the heat exchanger on 

a previously installed heater be sure that all electri-

cal power, the gas supply and water supply have been 

turned off before starting the procedure. These instruc-

tions have been written to include the steps needed 

when reversing the water connections on an existing 

installation. If you are reversing the headers on a new 

installation, some steps will be ignored. 

When an automatic chemical feeder is installed 

in the plumbing, it must be installed downstream of 

the heater (see Section 5.7). A check valve must be 

installed between the heater and the chemical feeder to 

prevent back-siphoning of chemically saturated water 

into the heater where it will damage the components.

5.4 

automatic Flow Control Valve

The inlet/outlet header of the Legacy Model LRZ 

millivolt heater comes equipped with an automatic 

flow control valve. The automatic flow control valve 

maintains the proper flow through the heater at rates 

up to approximately 475 lpm. If the filter system flow 

rate is higher than approximately 475 lpm, install a 

manual bypass valve (see Figure 6), then perform a 

temperature rise test (see Section 11.6) and adjust the 

flow using the bypass valve until the proper tempera

-

ture rise is obtained.

AQUAPURE

MANUAL BY-PASS DETAIL
MANUAL BY-PASS IS USED
WHEN FILTRATION RATE
EXCEEDS 125 GPM

Figure 6.  typical piping installation

Figure 7.  Hydraulic Head loss Curve

Содержание Legacy LRZ









































Отзывы: