Zippie Salsa M Скачать руководство пользователя

Страница: 67 / 72

ZIPPIE SALSA & SALSA

Model: Zippie Salsa M (mid wheel drive)

max. load (Mass of the test

dummy): 75 kg

The wheelchair Zippie Salsa

conforms to the following

standards:

a) requirements and test

methods for static, impact

and fatigue strengths

(ISO 7176-8)

b) power and control systems

for electric wheelchairs

requirements and test

methods (ISO 7176-14)

c) climatic test in accordance

with ISO 7176-9

d) requirements for

resistance to ignition in

accordance with

ISO 7176-16

e) the product is specified as

a Class B power chair

f) all materials used on this

product conform to EN1021

parts 1 and 2.

ISO7176-15

Min.

Max.

Comments

Overall length (with leg rest)

1050 mm with 90° hanger

Overall Width

600 mm

Total mass (w. batteries)

113 kg

145 kg

Weight of the heaviest individual part

98 kg

Chair with all no tool removal parts taken

off

Static stability - downhill

17°

worst case 40 cm deep seat, 0° tilt, -4°

recline

Static stability uphill

10°

worst case 40 cm deep seat, 30° tilt, 30°

recline

Static stability - sidewards

13.9°

worst case 40 cm deep seat, 0° tilt, 0°

recline

Energy consumption (max. range)

26 km

Dynamic stability uphill

8 °

9° tilt/16° recline &max. seat height (not

with balle)

Obstacle climbing (with kerb climber)

75 mm

Forward with 6 kph motors

Max. Speed forward

6 kph

10 kph

10 kph only with 10 kph motor option

Min. Braking distance from maximum

speed

1.0 m

1.2 m

1 m for 6 kph motor, 1.2 m for 10 kph

motor

Seat plane angle

-5°

30°

-5° only with MBL tilt + additional brackets

Effective seat depth

302 mm

402 mm

20 mm increments

Effective seat width

302 mm

402 mm

20 mm increments

Seat height at the front edge

470 mm

set 0° tilt, lowest seat height and no

modules

Backrest angle

-4°

16°

adjustable in 4° steps with tools

Back height

385 mm

435 mm

25 mm increments

Footrest to seat distance

165 mm

360 mm

with 70° hanger

Leg to seat surface angle

110°

with 70° hanger

Armrest to seat distance

150 mm

225 mm

adjustable with tools

Front position of the armrests

240 mm

315 mm

Min. turning radius

670 mm

with 70° hanger

Nominal battery voltage

24 V

Battery cut-off voltage

16 V

for 255 seconds

Battery fusible links

150A in line fuse on each battery

Quickie Direct Actuator Control Box

fusible link

15A blade fuse located on AUX supply of

power loom

Mass of the test dummy

75 kg

EN 12184

Min.

Max.

Comments

Max. kerb height

75 mm

Ground clearance

40 mm

Turning Diameter

1000 mm 1150 mm

Speed control operation force

2 N

Direction control operation force

1 N

Содержание Salsa M









































































Результаты поиска

Содержание Salsa M

Отзывы:

Похожие инструкции для Salsa M

Бренды по названию

Популярные бренды

Zippie Salsa M, Инструкция по применению

Результаты поиска

Содержание Salsa M

Отзывы:

Похожие инструкции для Salsa M

Бренды по названию

Популярные бренды