Zip HydroTap G4 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 36

Zip HydroTap G4 Скачать руководство пользователя страница 7

802253UK - Boiling chilled residential installation instructions - Aug 2015 - V2.02

Page 7 of 36

Warnings and regulatory information

Warnings

•

The Zip HydroTap

®

G4 must be earthed. The resistance of the earth

connection from each exposed metal part must be less than 1Ω.

• All installation and service work must be completed by trained and

suitably qualified tradespeople. Faulty operation due to unqualified

persons working on this product, or any other Zip product may void

warranty coverage.

• As the installer, it is your responsibility to supply (if necessary)

and install all valves as required by local regulations and relevant

standards.

• The HydroTap

®

G4 is rated for 230V 50Hz AC operation.

• Do not remove the cover of the appliance under any circumstances

without first isolating the appliance from the power supply.

• Never locate the Command-Centre

TM

near, or clean with water jets.

• Do not expose the Zip HydroTap

®

G4 to the elements of nature.

• Due to the process of continuous improvement, Zip Heaters reserves

the right to change details mentioned in this manual, without notice.

• Visit www.zipheaters.co.uk to ensure you have the latest copy of this

document.

«
...
5
6
7
8
9
...
»

Содержание HydroTap G4





































Отзывы:

Нет отзывов