Zip HydroTap G4 Скачать руководство пользователя страница 20

Страница: 20 / 36

Page 20 of 36

802253UK - Boiling chilled residential installation instructions - Aug 2015 - V2.02

Installation instructions

Installing the All-in-One ‘Vented’ tap

(see page 30 for Command-Centre

installation).

1.19 All-in-One ‘Vented’ connections.

• Connect the red, blue and clear silicone tubes &

USB cable to the Command-Centre

as shown.

• Working from inside the cupboard, attach

the braided hoses to the tube extensions

(ensure the seals on the end of the hoses are

lubricated). Check the correct position for mixer

and ambient connections by matching the

colours on the braided hoses with the coloured

markings on the extension tubes. (See adjacent

diagram).

• Connect the braided hose with the blue marking

to the ‘MIXER IN’ on the Command-Centre

• Connect the braided hose with the white

marking to the Restrictaflow.

• Connect the braided hose with the red marking

to the metal tube, with red marking then to the

‘MIXER OUT’ on the Command-Centre

• Ensure that all tubes and hoses are firmly

secured.

Braided hose

connection to metal

tube - ‘MIXER

OUT’ on Command-

Centre

Braided hose with

blue marking - to

MIXER IN’

on Command-

Centre

Clear silicone

tube - VENT on

Command-Centre

Braided hose with

white marking -

Restrictaflow on

ambient supply

Red silicone tube -

BOILING OUT on

Command-Centre

Blue silicone tube

- CHILLED OUT

on Command-

Centre

1.18 Base block spider markings and silicone tube positions

(viewed from

underneath).

White marking

Blue marking

USB cable

Blue silicone tube

Red silicone tube

Clear silicone tube

Braided hose with

white marking

Braided hose with

blue marking

Braided hose with

red marking

RED

CLEAR

BLUE

BRAIDED

POWER

CABLE

USB

MAINS

MIXER

OUT

MIXER

BOILING

OUT

BYPASS

VENT BYPASS

OUT CHILLED

OUT

Booster

HT Mixer

connections

BRAIDED

Содержание HydroTap G4





































Результаты поиска

Содержание HydroTap G4

Отзывы:

Zip HydroTap G4, Руководство по установке, Страница: 20 / 36

Результаты поиска

Содержание HydroTap G4

Отзывы: