manualshive.com logo in svg

Zip HydroTap G4, Руководство по установке, Страница: 18 / 36

Поделиться
Скачать
Zip HydroTap G4 Скачать руководство пользователя страница 18

Page 18 of 36 

   802253UK - Boiling chilled residential installation instructions - Aug 2015 -  V2.02

   Installation instructions

Installing the All-in-One 'Mains' tap

1.15 All-in-One ‘Mains’ connections

•  Connect the red, blue and clear silicone tubes & 

USB cable to the Command-Centre

TM

 as shown.

•  Working from inside the cupboard, attach 

the braided hoses to the tube extensions 

(ensure the seals on the end of the hoses 

are lubricated). Check the correct position for 

hot and ambient connections by matching the 

colours on the braided hoses with the coloured 

markings on the copper extension tubes. (See 

adjacent diagram).

•  The braided hose with the blue markings must 

be connected to the ambient mains supply. 

•  The braided hose with the red markings must 

be connected to the hot mains supply. 

•  Do not over tighten the braided hoses.
•  Ensure that all tubes and hoses are firmly 

secured.

Blue silicone tube - 

CHILLED OUT on 

Command-Centre

TM

Clear silicone 

tube - VENT on 

Command-Centre

TM

Red silicone tube - 

BOILING OUT on 

Command-Centre

TM

Braided hose with blue 

marking - ambient 

domestic supply.

Braided hose 

with red marking 

- hot domestic 

supply.

Note

 All silicon / 

plastic tubes must be 

cut to size. They must 

have a constant fall 

back to the 

Command-Centre

TM

.

1.14 Base block spider markings and silicone tube positions 

(viewed from 

underneath).

Blue marking

Red marking

USB cable

Blue silicone tube

Red silicone tube

Clear silicone tube

 

(see page 29 for Command-Centre

TM 

connections)

Braided hose with 

blue marking

Braided hose with 

red marking

RED

CLEAR

BLUE

BRAIDED

POWER

CABLE

USB

MAINS 

IN

MIXER 

OUT

MIXER 

IN

BOILING 

OUT

BYPASS 

IN

VENT BYPASS 

OUT CHILLED 

OUT

Содержание HydroTap G4





































Отзывы:

Нет отзывов