background image

Page 4 of 20  

          

 

        HydroTap Installation and Operating Instructions 

These Installation Instructions cover the A and AV HydroTap range. Use the chart 
on the left to identify the model you are using:

Commercial  Models:

= Boiling / Chilled and Hot / Cold.  (Mains)

AV   = Boiling / Chilled and Hot / Cold.  (Vented)

Boiling Water Capacity:

160 = 160 cups in one hour**   240 = 240 cups in one hour** 

** Capacity will be reduced by the volume of water used when operating the mixer tap.

Chilled  Water Capacity: (BCH only)

125 = 125 glasses in one hour   175 = 175 glasses in one hour

Note: 

The 

Cup

 measurement = 167mls, the 

Glass 

measurement = 200mls.

Before installing ensure that the following have been provided at the 
installation site:

•  Sufficient space in the cupboard to install the undersink unit in accordance 

with these Installation Instructions. A table of dimensions is given above.

NOTE: Add 65mm to the Depth of the undersink unit to allow for Water 
and Electrical connections. 

•  A water supply connection with isolating valve inside the cupboard 

within reach of the 750 mm flexible connection and positioned so that 
the connection point and the stop cock will not be obstructed when the 
undersink unit is installed.

Installation requirements

AV

Model 

160

Cups of 

Boiling Water 

per Hour

125

Glasses of 

Chilled Water 

per Hour

Frost Protection

If this appliance is located where the ambient air temperature could fall below 5ºC when the heater is not in use, do not 
turn off the appliance electrically. This safeguard does not offer the same protection to the connecting pipework and 
fittings.

Altitude 

The  HydroTap is equipped with a self-calibrating program which caters for altitude adjustment.       

Installation Environment Considerations

This unit is intended for indoor use only and should never be installed outdoors or exposed to the elements of nature. 
This unit must not be positioned in an area that may be cleaned by a water jet. This unit must not be cleaned by a water 
jet.

NOTE:

HydroTaps are designed to operate within 1ºC to 2ºC of boiling point and at 5ºC to 10ºC for chilled drinking water.

Read these warnings 

continued

    Commercial models covered by these instructions

Model

Height             

mm (inch)

Depth                  

mm (inch)

Width                   

mm (inch)

Weight  empty         

kg’s  lbs

Weight  full                 

kg’s  lbs

160/125

337 (13.2)

473 (18.6)

440 (17.3)

28 (61.7)

35 (77.1)

240/175

395 (15.5)

508 (20)

500 (19.6)

29.5 (65)

38 (83.7)

Содержание HydroTap All-In-One 89650





















Отзывы: