Zimmer GEH8660-B Скачать руководство пользователя

Страница: 34 / 54

►

Activate the example project.

The changed parameters have been applied to the drive control unit.

The connection between the

IndraWorks Ds

software and the drive

control unit is canceled.

►

Start the

IndraWorks Ds

software.

►

In the navigation pane, click

Axis [1]

►

Click

Master Communication Axis [1]

►

Click

Settings

►

Click the

Process Data In (AT)

tab.

The input parameters are displayed in the

Process Data In (AT)

tab.

►

Check the input parameters by clicking the

links

Signal Status Word

and

Signal Control

Word

The default bits

signal status word

and

signal

control word

are already stored in the included

parameter set.

►

Click the

Process Data Out (AT)

tab.

The output parameters are displayed in the

Process Data Out (AT)

tab.

►

Check the input parameters by clicking the

links

Signal Status Word

and

Signal Control

Word

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

INSTALLATION AND OPERATING INSTRUCTIONS:

GEH8000

DDOC00262 / e

EN / 2023-03-06

Содержание GEH8660-B























































Результаты поиска

Содержание GEH8660-B

Отзывы:

Похожие инструкции для GEH8660-B

Бренды по названию

Популярные бренды

Zimmer GEH8660-B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GEH8660-B

Отзывы:

Похожие инструкции для GEH8660-B

Бренды по названию

Популярные бренды