Zimmer GEH8660-B Скачать руководство пользователя

Страница: 16 / 54

11 Commissioning

11.1 Checking operational readiness

►

Check the energy supply.

►

Check all mounting screws for the prescribed tightening torque.

11.2 Easy Startup
11.2.1 Setting the IP address

►

Define the IP address for the drive control unit.
• Standard: 192.168.0.1

►

Enable the IP range on your computer for the entry of the IP address in the drive control unit via the control panel.

►

Press the

Enter

button.

►

Navigate by pressing the



buttons.

►

Navigate to the

Ethernet

entry.

►

Press the

Enter

button.

The selection has been confirmed.

►

Press the

Enter

button.

The

IP-Addr

entry is shown.

►

Set the IP address by pressing the



button.

►

Press the

Enter

button.

The input has been confirmed.

►

Restart the drive control unit.

INFORMATION

The software

IndraWorks Ds

IndraWorks Engineering

is required for initial commissioning.

This setting can vary in other software versions.

►

Please consult the software manufacturer to learn how to use the software version available to you.

Zimmer GmbH shall accept no liability for any damage caused by improper use. The operator bears sole

responsibility.

►

Start the

IndraWorks Ds

software.

►

Enter the IP address in the

IndraWorks Ds

software and the computer.

►

Click the

Search

button.

Found drive control units are shown in the

Connection Selection

window.

►

In the

Connect

column, enable the option

field of the desired drive control unit.
• The IP address of the drive control unit

must match.

►

Click the

button.

The connection to the drive control unit is

established.

The main window of the

IndraWorks Ds

software opens after successful connection.

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

INSTALLATION AND OPERATING INSTRUCTIONS:

GEH8000

DDOC00262 / e

EN / 2023-03-06

Содержание GEH8660-B























































Результаты поиска

Содержание GEH8660-B

Отзывы:

Похожие инструкции для GEH8660-B

Бренды по названию

Популярные бренды

Zimmer GEH8660-B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GEH8660-B

Отзывы:

Похожие инструкции для GEH8660-B

Бренды по названию

Популярные бренды