Zimmer GEH8660-B Скачать руководство пользователя

Страница: 19 / 54

11.2.3

Loading axis-specific parameter sets

►

In the

Configuration

menu, click

Load

The

Load Parameters

window opens.

►

Enable the option field of the desired

parameter set.

►

Click the

Load

button.

The

Load Parameters

window closes.

The software notifies you before transmitting that the drive control unit

must be in configuration mode.
If the drive control unit is already in configuration mode, this message will

not appear.

►

Follow the instructions in the message.

►

Click the

Yes

button.

The transfer of the parameter set to the drive control unit starts.

INFORMATION

After the parameter set has been successfully transmitted to the drive control unit, it must be restarted. To do this,

you can either briefly disconnect the drive control unit's power supply or use the

IndraWorks Ds

software to

reboot.

INSTALLATION AND OPERATING INSTRUCTIONS:

GEH8000

DDOC00262 / e

EN / 2023-03-06

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

Содержание GEH8660-B























































Результаты поиска

Содержание GEH8660-B

Отзывы:

Похожие инструкции для GEH8660-B

Бренды по названию

Популярные бренды

Zimmer GEH8660-B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GEH8660-B

Отзывы:

Похожие инструкции для GEH8660-B

Бренды по названию

Популярные бренды