manualshive.com logo in svg

ZIEHL-ABEGG ECblue Series, Руководство по сборке

Поделиться
Скачать
ZIEHL-ABEGG ECblue Series Скачать руководство пользователя страница 35

Watchdog Mode

Watchdog Mode:
0: No function (default) = OFF from FW 13
1: Fault (K1 function, h15) in case of communication fault (WDT)
2: Constant speed 1 * in case of communication fault (WDT)
3: Fault + constant speed 1 * in case of communication fault (WDT)
4: Fault by E1 Fault ** (only ECblue)
5: Constant speed 1 by E1 Fault (only ECblue)
6: Fault constant speed 1 in case of E1 fault (only ECblue)

*  in this condition it is possible by digital input function 5, 6 or digital control function to 
change between the constant speeds (Holding register h4).

** E1 fault is triggered when E1 falls below E1 min x 0.5. E1 fault is cancelled when E1 
rises above E1 min x 0.9.

8.6.5

Networking via MODBUS 

It is possible to network several devices with each other. The device uses the MODBUS-RTU as the 
protocol for the RS-485 interface.

Bus Address

The device address is factory set to the highest available MODBUS address: 247.   
Setting range MODBUS Address: 1 - 247. 

UART Baudrate

Setting transfer rate 
Valid values: 4800, 9600, 19200, 38400
Factory setting: 19200

Illegal value: 115200 

UART Mode

Setting transfer format 
Valid values: 8O1, 8N1, 8E1
Factory setting: 8E1

Information

If it is attempted to change the baud rate to an impermissible value (e.g. 115200), the following 
exception code will be sent back:

|

Exception Code 3: Illegal Data Value

|

.

8.7

Menu group 

“

Motor Setup

”

 Motor Setup

Rated speed

 

Motor rated current

*The following controller presets are dependent on the re-
spective motor design. 
These are shown for informational purposes and must only 
be changed after consultation with ZIEHL-ABEGG and enter-
ing a password.

•

Rated speed

•

Motor rated current

•

Rotat. Direction

•

Value motorheating

Rampup time 

Assembly instructions 

ECblue

Programming by hand held terminal A-G-247NW

L-BAL-F055D-GB 1634 Index 002

Part.-No. 

35/51

Содержание ECblue Series




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды