ZIEHL-ABEGG ECblue Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 51

ZIEHL-ABEGG ECblue Series Скачать руководство пользователя страница 13

4.6.4

Optimal installation distances according to for RH../ ER../ GR.. fans

•

Distance on suction side: LA

≥

0.5 x DSa *

•

Distance on the pressure side: LD

≥

1 x DSa

•

Impeller blade external-diameter :

Ø

DSa

•

Housing wall distances: A = 1.8 x DSa (A = B)

* In the case of disturbance

ﬂ

ow (per example curved pipe at the suction side,

ﬂ

aps etc.) LA

≥

1 x DSa

4.7

Mounting the motor

Motors design MK

Fastening to

ﬁ

xed motor

ﬂ

ange

(assembly of axial fans / fans of design A, D ..) and (assembly of

radial fans of design RH).

•

If the motor is used to drive fan impellers or other components, please note the maximum
permissible speeds of the impeller or the component to be driven.

•

The max. permissible mass of the impeller ort he component to be driven must be inquired from
and con

ﬁ

rmed in writing by ZIEHL-ABEGG.

Design K (with rotor

ﬂ

ange) or D (with offset rotor

ﬂ

ange) as a drive for fans:

•

During assembly of the fan impellers or other components, no inadmissible force may be applied to
the motor bearing.

•

Centre the fan impeller accurately and mount without tension on the rotor

ﬂ

ange, the fan wheel

must lie

ﬂ

at.

•

Use suitable screws for fastening the fan impeller on the rotor

ﬂ

ange and

ﬁ

t as suitable screw lock.

•

Every screwing case must be tested for suitability.

•

The permissible area pressing of the rotor

ﬂ

ange may never be exceeded (depending on the

contact surface).

•

Too great a screw overhang is not permitted and can lead to scraping or blocking of the rotor on the

ﬁ

xed motor

ﬂ

ange.

•

Motors are not balanced as standard, a complete balancing with mounted fan impeller is necessary.
The balancing must be done on the fan impeller. The pertinent regulations must be observed.

Permissible tightening torques M

A

Thread size

M6

Property class 8.8, friction coefcient

µ

ges = 0.12

9.5 Nm

Screw penetration

≥

1.0 x d

Max. permissible screw overhang

1.0 mm

Assembly instructions

ECblue

Mounting

L-BAL-F055D-GB 1634 Index 002

Part.-No.

13/51

«
...
11
12
13
14
15
...
»

Содержание ECblue Series




















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды