Zhen Optics Z2812U, Руководство пользователя

Страница: 23 / 30

42 43
5 1 2 Camera control command . .
Command Function Command packet Note
AddressSet Broadcast 88 30 0p FF p VISCA Address :
IF Clear Broadcast 88 01 00 01 FF I F Clear _ /
CommandCancel 8x 21 FF
CAM Power _
On 8x 01 04 00 02 FF
Power ON OFF /
Off 8x 01 04 00 03 FF
CAM Zoom _
Stop 8x 01 04 07 00 FF
Tele Standard 8x 01 04 07 02 FF ( )
Wide Standard 8x 01 04 07 03 FF ( )
Tele Variable 8x 01 04 07 2p FF ( )
p 0 low F high = ( ) - ( )
Wide Variable 8x 01 04 07 3p FF ( )
Direct
8x 01 47 0p 0q 04
0r 0s FF
pqrs Zoom Position :
CAM Focus _
Stop 8x 01 04 08 00 FF
Far Standard 8x 01 04 08 02 FF ( )
Near Standard 8x 01 04 08 03 FF ( )
Far Variable 8x 01 04 08 2p FF ( )
p 0 low F high = ( ) - ( )
Near Variable 8x 01 04 08 3p FF ( )
Direct
8x 01 04 48 0p 0q
0r 0s FF
pqrs Focus Position :
Auto Focus 8x 01 04 38 02 FF
Manual Focus 8x 01 04 38 03 FF
CAM _
Zoom Focus
Direct
8x 01 04 47 0p 0q
0r 0s
0t 0u 0v 0w FF
pqrs Zoom Position :
tuvw Focus Position :
CAM WB _
Auto 8x 01 04 35 00 FF
3000K 8x 01 04 35 01 FF
4000k 8x 01 04 35 02 FF
One Push mode 8x 01 04 35 03 FF
5000k 8x 01 04 35 04 FF
Manual 8x 01 04 35 05 FF
6500k 8x 01 04 35 06 FF
Ack Completion / Message
Command packet Note
ACK z0 41 FF Returned w he command is accepted hen t .
Completion z0 51 FF
Returned when the command has been
executed.
z camera address 8 = +
Error Messages
Command
packet
Note
Syntax Error z0 60 02 FF
Returned mat is different or when the command for
when a command with illegal command parameters
is accepted
Command
Not
Executable
z0 61 41 FF
Returned t be executed due when a command canno
to current conditions For example when commands . ,
controlling the focus manually received during are
auto focus.
U n d e r c o m m o n w o r k i n g c o n d i t i o n , t h e c a m e r a c o u l d b e c o n t r o l l e d t h r o u g h
RS232/RS485 interface(VISCA),RS232C serial parameter are as follows:
: 2400/4800/9600/115200 bits / sec; Start bit: 1; data bits: 8; Stop bit:
1;Parity: None.
After power on, the camera first go left, then back to the middle position. initial
configuration is finished after the zoom moved to the farthest and then back to the
nearest position. If the camera saved 0 preset before, it will be back to that position
after initialization. At this point, the user can control the camera by the serial commands.
Baud rate
5.1.1 Camera return command
5.1 VISCA protocol list
5.Serial Communication Control
!"#$
Information and Communication PTZ Camera
!"#$
Information and Communication PTZ Camera