background image

 

AEROLYTE 6060A and 7070A G2 PRESSURE CABINETS 

Page 27 

 

 

 

 

 

© 2016 CLEMCO INDUSTRIES CORP.  

  www.clemcoindustries.com  

  Manual No. 27789 Rev. A, 10/16 

9.5 

Cabinet Replacement Parts, Figure 31

 

 

Item Description 

Stock 

No.

 

 

  1. 

Gasket, door, adhesive-backed, per foot, 

 

24 ft. for 6060A, 28 ft. for 7070A  ........... 21236 

  2. 

Light assembly, does not include lamps,  

 

use 48", T-8, 32 watt lamps  ................... 25300 

  3. 

Grate, slotted front  

 for 

6060A  ............................................... 25155 

 for 

7070A  ............................................... 12971 

 4. 

Grate, unslotted 

 for 

6060A  ............................................... 25154 

 

for 7070A (3 required)  ........................... 12970 

  5. 

Glove set  

 Band-clamp 

attachment  ........................ 11215 

 

Quick-Change (clampless) attachment .. 28820 

  6. 

Glove, left hand only  

 Band-clamp 

attachment ......................... 12710 

 

Quick-Change (clampless) attachment .. 28638 

  7. 

Glove, right hand only  

 Band-clamp 

attachment ......................... 12711 

 

Quick-Change (clampless) attachment .. 28639 

  8. 

Clamp, for clamp-attached glove  .............. 11576 

 9. 

Grommet, blow off hose  ........................... 11798 

 10 

Grommet, blank  ........................................ 13666 

 11. 

Support adaptor, blast hose  ..................... 16554 

 12. 

Gasket, blast hose support adaptor  ......... 13426

 

 13. 

Muffler, outlet  ............................................  05068 

 14. 

Foot pedal assembly, 

 less 

tubing  ............................................. 20483 

 with 

tubing, 

14 feet  ................................ 20195 

 15. 

Actuator bracket, door interlock  ................ 19152 

 16. 

Over-travel stop, door interlock  ................ 20004 

 17. 

Detent sleeve, door interlock  .................... 15042 

 18. 

Valve, 1/8", 3-way air, door interlock  ........ 12202 

 19. 

Fitting, straight,, 1/8" NPT x 1/8" barb  ......... 11732 

 20. 

Eyebolt, 5/8"  ............................................. 13421 

 21. 

Regulator, 1/4-NPT pilot with gauge ......... 12050 

 22. 

Gauge, pressure,1/8" cbm  ........................ 01908 

 23. 

Bushing 1/4" x 1/8" NPT  ................................ 02010 

 24. 

Fitting, 1/8" NPT elbow x 1/8" barb  .......... 11733 

 25 

Elbow, 1/4-NPT brass st.  .......................... 02027 

 26. 

Gasket, 5/16" x 1" adhesive-backed,  

 

per foot, specify feet required  ................ 00187 

 27. 

Glass w/frame, replacement  ..................... 25301 

 28. 

Intake stack w/damper  ............................. 23156 

 29. 

Baffle, air intake  ........................................ 25912 

 30. 

Nipple, 1" x close  ...................................... 01701 

 31. 

Tee, 1" pipe ............................................... 01789 

 32. 

Plug, 1" pipe  ............................................. 01761 

 33. 

Nut, 1" lock  ............................................... 11917 

 

 
 
 

 

 

Figure 31 

 

28

9, 10 

13 

1

26

2

15

26

29

20

11 

  5 

12 

27

16 

15 

17 

18  199 

19 

31 
32 

30 

33 

14

  5 

21 

22 

23 
24 

25 

24 

23 

Содержание AEROLYTE PRN 6060-A


































Отзывы: