Zennio ZVI-TMDP4 Скачать руководство пользователя

Страница: 33 / 61

Touch-MyDesign Plus

http://www.zennio.com

Technical Support:

http://zennioenglish.zendesk.com/

2.2.2

ADDITIONAL BUTTONS

The following is a list of the functions (joint or individual) that can be assigned to the

five additional buttons of the device.

Temperature Setpoint.

1-Byte Control (Unsigned Int.)

1-Byte Control (Scaling)

Individual Buttons

(each additional button will work independently):



Disabled.



Binary.



Hold & Release.



Two Objects (Short Press / Long Press).



Scene.



Scaling Constant.



Counter Constant.



Float Constant.



Dimmer.



Shutter.

The next sections detail each of the above options.

ETS PARAMETERISATION

Figure 24

Additional Buttons - Configuration

As stated in section 2.1, an independent tab for the parameterisation of the additional

buttons is shown in ETS by default. This tab comprises another one named

“

Configuration

”, containing one parameter:

Function

: sets the desired function for the additional buttons. The options are

“Temperature Setpoint” (default selection), “1-Byte Control (Unsigned Int)”, “1-

Содержание ZVI-TMDP4






























































Результаты поиска

Содержание ZVI-TMDP4

Отзывы:

Похожие инструкции для ZVI-TMDP4

Бренды по названию

Популярные бренды

Zennio ZVI-TMDP4, Руководство пользователя

Результаты поиска

Содержание ZVI-TMDP4

Отзывы:

Похожие инструкции для ZVI-TMDP4

Бренды по названию

Популярные бренды