Zennio KEM Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 49

Zennio KEM Скачать руководство пользователя страница 35

KEM

http://www.zennio.com

Technical Support:

http://support.zennio.com

35

2.6

ALARMS

In addition to notifications, KEM implements 7 alarms to monitor

electric power

,

electric

current

and

water flow

, which can be enabled and parameterised independently.

It will be possible to set an upper and a lower limit for any of the variables. When these

limits are exceeded, the device will send a binary value through the different objects.

The deactivation of the alarm after

exceeding the limit

shall be effective when the value

of the variable is less than the upper limit minus the hysteresis. In the same way, the

deactivation of the alarm after falling

below

the

lower limit

will become effective when

the variable exceeds the lower limit plus the hysteresis.

ETS PARAMETERISATION

The Alarms tab will become visible once the Alarm function has been enabled in the

“General” screen (see section 2.1).

Figure 26.

Alarms

– Configuration

“Alarm n” tab will become visible once some of the alarms have been enabled.

2.6.1

ALARM N

In this tab both the variable to be used for the alarm and the upper and lower limits for

activating the alarm can be configured.

«
...
33
34
35
36
37
...
»

Содержание KEM


















































Отзывы:

Нет отзывов