background image

804050NZ- CS Commercial HydroTap - Installation Instructions - 09.2016 v3.01 

Page 13 of 20

4.1

 

Hose and tube fitting

 

• 

Remove all caps from the top of the undersink unit. 

• 

Fit the foam insulation to the Blue and to the White tubes after trimming them to length.

• 

Flush the supply line before fitting to the undersink unit.

• 

Install the mains water braided hoses to the undersink unit before locating the unit in place. 

Section 4 

Underbench Unit Installation

John Guest

 

fittings 

(Insertion and removal)

Be careful when cutting the poly tube so that there are no rough edges and that the tube is not distorted. 

1. 

Use a sharp knife to ensure the tube has a clean, straight edge. Do not cut at an angle.

2. 

Remove any swarf or unwanted material.

3. 

Push the tube into the John Guest fitting making sure all connections to the John Guest fittings are 
pushed in past the “O”ring to full depth, at least 15-16mm.

4. 

Check for a good joint by pulling back on the tube. If the tube comes out, of the fitting, repeat the 
above step.

5. 

To remove the tube, press the collet into the fitting and at the same time pull back on the tube.

Installation

Содержание HydroTap





















Отзывы: