25
ZCM3821-001_v01
●
Select the appropriate cup size on the appliance.
●
Adjust the outlet height accordingly by pushing the outlet up or down and then place
a container under the coffee outlet.
●
Open the rotary switch for milk froth/hot water to obtain hot water.
●
You can stop hot water output at any time by closing the rotary switch for milk froth/
hot water.
The milk tube must not be connected when preparing hot water.
The “Milk froth” function must not be selected.
SETTING THE GRINDING FINENESS
You can set the the grinding fineness with the help of the lever.
Only set the grinding fineness when the grinder is running.
To set the grinding fineness, proceed as follows:
●
Place a cup under the coffee dispensing spout.
●
Press
(button
6
) to prepare the coffee.
6
5
4
3
2
●
Adjust the grinding fineness with the grinding fineness lever while the grinder is
running. The coffee is prepared and the grinding fineness is set.
The setting is implemented as follows:
fine ground for “intensive taste”
medium ground for “normal taste”
coarse ground for “mild taste”
For light roasted coffee beans, set the grinding mechanism to “fine”. If the
grinding fineness is set too fine, the coffee will be dispensed a drop at
a time.
For dark roasted coffee beans, set the grinding mechanism to “coarse”. If the
grinding fineness is set too coarse, the coffee will be dispensed too quickly.
PREPARING COFFEE WITH WHOLE COFFEE BEANS
To prepare coffee with whole coffee beans, proceed as follows:
●
Set one or two cups, or if pots are selected, a pot with the appropriate volume (500 or
1000 ml) under the coffee outlet.
●
In order to reduce heat loss and splashing, adjust the dispensing spout height to suit
your cup size by moving it up or down.
If the height adjuster is difficult to move, clean it. Refer to Chapter
“REMOVING AND CLEANING THE COFFEE DISPENSING UNIT”.
●
Select the desired cup size by pressing the button
4
.
6
5
4
3
2
The following selections are possible:
Coffee mug
approx. 190 ml
Coffee cup
approx. 120 ml
Espresso cup
approx. 40 ml
The selection of cup size is only possible in one or two-cup mode. The
default factory setting (approx. 120 ml per cup) is set for the four or eight
cup mode in the pot selection.
The coffee machine is set for standard quantities for each cup size by
default. If you wish to change any of the cup filling quantities, instructions
can be found in section “CHANGING AND STORING THE CUP FILLING
LEVEL IN BEAN MODE”.
●
Select the desired ground coffee quantity by pressing the button
5
.
6
5
4
3
2
The following selections are possible:
”Mild“
”Medium“
”Intensive“
”Powder“
An automatic grinding quantity correction measures the ground coffee
quantity and adapts this gradually to the set value for the coffee strength.
This compensates the differences between the grinder and various
different coffee varieties. It may therefore be necessary to brew 5 times
until the correction is perfect.
The last-selected ground coffee quantity remains set for each cup size.
The set ground coffee quantity remains stored even when the coffee
machine is switched off.
●
Select the required number of cups or pot size by pressing button
3
.
6
5
4
3
2
The following selections are possible:
”1 cup“
”2 cups“
”pot (4 cups)“
”pot (8 cups)“
●
Press
(button
6
) to heat the coffee.
6
5
4
3
2
Remember that in two cup mode, two brewing operations are implemented
in sequence and correspondingly, if a pot is selected for four/eight cup
mode, 4 or 8 brewing operations are implemented. Only remove the cups
or pot when all brewing operations are finished.
During coffee preparation, the coffee powder is moistened with a small
amount of water first for pre-brewing. The actual brewing process takes
place after a short pause.
Содержание ZCM3821B
Страница 37: ...ZCM3821 001_v01 ...
Страница 38: ...ZCM3821 001_v01 ...
Страница 39: ...ZCM3821 001_v01 ...
