26
ZCM3821-001_v01
You can stop coffee dispensing prematurely by briefly pressing
(button
6
). In the case of strongly uneven or only one-sided cup filling
during 2-cup operation, check whether one or both coffee dispensing
spouts are blocked on the inside by foreign bodies (coffee bean or similar).
CHANGING AND STORING THE CUP FILLING LEVEL IN BEAN MODE
The coffee machine is set for standard quantities by default. However, you can set the cup
filling level individually for each cup size. Proceed as follows:
●
Press the button
4
repeatedly until the required cup symbol for the desired ground
coffee quantity is displayed.
6
5
4
3
2
The cup filling level for one cup is stored during this process. (Appliance
must be set to one cup mode).
●
Place an appropriate cup under the coffee delivery spout (Espresso cup, coffee cup
or coffee mug).
●
Press key
5
repeatedly until the symbol for the required coffee grinding quantity
lights up.
6
5
4
3
2
●
Press
(button
6
) and keep it pressed until the desired filling amount is reached.
6
5
4
3
2
●
Release the button. The new cup filling level is now stored.
Repeat the procedure if you also wish to change the filling level for the
other cup sizes.
All values remain stored even when the coffee machine is switched off.
Should you change your cup size, you can adapt the cup filling level
individually at any time.
The stored cup filling levels for each individual cup symbol only applies in
bean mode.
PREPARING COFFEE WITH POWDERED COFFEE
Ensure that you only use the measuring spoon supplied and never fill
than the container with more than one level measuring spoon (max. 8 g) of
coffee powder.
Do not fill the container with water-soluble, freeze-dried instant products
or other drink powders.
Too finely ground coffee powder can lead to faults.
To prepare coffee with powdered coffee, proceed as follows:
●
Select the “Coffee powder” function by pressing the button
5
.
6
5
4
3
2
The following symbol lights up in the display:
During preparation of coffee with powder, only one cup can be prepared
with powdered coffee.
The “ground coffee quantity” function is deactivated. Therefore no
information on the ground coffee quantity appears on the display.
●
Select the desired cup size by pressing the button
4
.
6
5
4
3
2
The following selections are possible:
Coffee mug
approx. 190 ml
Coffee cup
approx. 120 ml
Espresso cup
approx. 40 ml
The standard filling quantities for each single cup symbol apply to bean,
powder and hot water mode. If you wish to change the cup filling quantities,
they only apply to powder mode. Instruction can be found in section
“CHANGING AND STORING THE CUP FILLING LEVEL IN POWDER MODE”.
●
Open the lid of the coffee bean container and the coffee powder shaft.
●
Pour in the fresh coffee powder.
●
Then close both lids again.
Ensure that powder does not clog the container and that no foreign matter
gets into the container.
Never fill the container with more than one level measuring spoon of coffee
powder.
The filling container is not a storage container; the powder must be
transported directly to the brewing unit.
●
Place a cup under the coffee dispensing spout.
●
In order to reduce heat loss and splashing, adjust the height of the dispenser to suit
your cup size by moving it up or down.
If the height adjuster is difficult to move, clean it. Proceed as described in
section “REMOVING AND CLEANING THE COFFEE DISPENSING UNIT”.
●
Press
(button
6
) to dispense coffee.
You can stop coffee dispensing prematurely by briefly pressing
(button
6
).
CHANGING AND STORING THE CUP FILLING LEVEL IN POWDER MODE
The coffee machine is set for standard quantities by default. However, you can set the cup
filling level individually for each cup size. Proceed as follows:
●
Select the “Coffee powder” function by pressing the button
5
.
6
5
4
3
2
The following symbol lights up in the display:
Содержание ZCM3821B
Страница 37: ...ZCM3821 001_v01 ...
Страница 38: ...ZCM3821 001_v01 ...
Страница 39: ...ZCM3821 001_v01 ...
