29
Arrange the power supply cord, so that it is not hanging down
the table or counter and it could not be pulled or fastened.
2
Connect the plug of the power supply cord to the power
supply outlet.
Make sure, that before connecting the appliance to the power
supply, the speed control knob
(4)
is set in position
0
.
3
Assemble the blender jug
(3)
on the motor unit, so that
the
symbol on the motor unit
(8)
is in line with the mark
▼on the jug.
4
Lock the blender jug
(3)
turning it in clockwise direction,
so that the symbol on the motor unit
(8)
is in line with the
mark ▼on the jug.
The handle of the blender jug (3) shall be placed on the
right side of the appliance.
5
Put the ingredients into the blender jug
(3)
.
6
Do not fill over 1500 ml mark on the blender jug (3)
.
If you do so, the ingredients can lift the lid
(5)
when the motor
is started.
7
Before use of the stand blender, insert the lid
(5)
onto
the blender jug
(3)
so, that its protrusion is in line with the
protrusion on the jug.
ATTENTION: Before inserting the lid (5) moisturize the
gasket with water.
8
Insert the lid overlay
(1)
into the inlet in the lid
(5)
so, that
the protrusions of the overlay enter the cuts in the lid inlet
and turn it left or right until it moves.
Do not start up the stand blender without the lid
overlay (1), especially when solid ingredients shall be
used. They can be ejected through the inlet.
9
Switch on the mixing by turning the speed control
knob
(4)
to adequate position (
P
,
I
,
II
).
10
In order to stop the appliance turn the speed control knob
to position
0
.
11
P (PULSE) functions
Turning the knob into
●
P
(PULSE) position shall cause the
short operation of the appliance with maximum speed for
the time of holding the knob.
Do not operate the appliance for longer than 2 minutes,
●
otherwise it can be overheated.
In case you need to add some ingredients during the
●
stand blender operation, turn and lift the lid overlay
(1)
,
insert new ingredients through the inlet, then replace the
lid overlay
(1)
and turn it right until it moves.
Make sure, that the added ingredients shall not exceed
●
the volume inside the jug over 1500 ml mark on the
blender jug
(3)
.
After operation
In order to stop the appliance, turn the speed control knob
to position
0
.
Hold the motor unit
●
(8)
with one hand, catch the jug
handle with the other hand and remove it out of the
motor unit
(8)
turning it counter-clockwise.
Remove the lid
●
(5)
out of the blender jug
(3)
.
Unplug the appliance from the mains supply when not
●
in use.
Cleaning and maintenance
(Fig. C)
Clean after operation as soon as possible, to prevent
the pulp accumulation inside the jug (3).
1
Pour approximately 1 liter of water to the blender jug
(3)
and start-up the appliance for approximately 30 seconds and
hold the
P
(PULSE) button.
2
Then empty the blender jug
(3)
, turn it upside-down and
dry.
3
If necessary, clean the jug
(3)
, lid
(5)
, feeder opening
stopper
(1)
and blades
(6)
in warm water with wash-up liquid.
Then rinse it under clean running water and dry.
●
If you left the jug for longer time without cleaning and
●
some particles glued to the jug inner, use nylon brush.
We do not recommend cleaning the jug
●
(3)
, blades
(6)
,
lid
(5)
and feeder opening stopper
(1)
in dish washer.
Aggressive cleaning agents applied in such device can
influence negative the surface conditions.
4
Clean the outsider of the motor housing
(8)
with damp,
gentle cloth.
ATTENTION: Do not immerse the motor housing (8) in
water or other liquid.
Do not clean the outside of the housing
●
(8)
with
aggressive detergents such as emulsion milk or pastes,
etc. They can remove information graphic symbols.
Do not clean the transparent jug
●
(3)
with harsh sponges
or clothes.
After washing dry thoroughly all the parts of the
●
appliance.
Disassembling of cutting unit
Remove the plug of the power supply cord from the
●
mains supply outlet.
Empty the blender jug
●
(3)
.
Remove the lid
●
(5)
from the blender jug
(3)
. Turn the
blender jug
(3)
„upside down” and place on the flat and
firm surface.
Hold the blender jug
●
(3)
with one hand, and unscrew the
blade unit with the other hand (counter-clockwise).
Carefully remove the blade unit
●
(6)
including the
gasket
(7)
.
ATTENTION: The appliance blades are sharp. Handle
them carefully.
Содержание 32Z011
Страница 29: ...Notes ...
Страница 30: ...Notes ...
