background image

 

INTRODUCTION 

Fluar Illuminator Z mot. 

Notes on instrument safety 

Carl Zeiss 

 
 

 

05/2012 

435180-9060-701 

1.2

 

Notes on instrument safety 

 

Fluar Illuminator Z mot. may only be used for the applications described in this operating 

manual. The manufacturer cannot assume any liability for other applications of the instrument, 

including those of individual modules or single parts.  

 

Modifications and repairs to this instrument and any devices operated in combination with the 

microscope must be carried out by our service department or by authorized personnel only. The 
manufacturer accepts no liability for damage caused by unauthorized access to the interior of 

the instrument. Failure to comply with this shall also render any warranty claims invalid. 

 

 

The device may only be operated by instructed personnel. The instruments may only be 

operated by trained personnel who are aware of the possible dangers involved with microscopy 

and the application concerned. The microscope is a high-precision instrument whose 
performance may be impaired if handled improperly. 

 

 

 

The separate manufacturer's instructions must be observed and general safety requirements 
complied with when connecting and operating the HXP 200 C illuminator. 
The HXP 200 C  generates high-energy light with an invisible portion. Risk of dazzling or 

blinding! Never look directly into the light beam or light guide exit. 
The lamp used in the HXP 200 C becomes very hot during operation and has a high internal 

pressure in a heated state. Risk of fire or explosion! 
The lamp must be changed in accordance with the manufacturer's instructions.  
The illuminator may only be connected to a properly installed earthed power outlet. 

 

The mains plug of instruments with a metal housing (e.g. HXP 200 C) may only be connected 

to a socket with earth contact. The protective capacity must not be rendered ineffective by 

using an extension cable without a ground wire. 

 

If it is determined that protective measures are no longer effective, the instrument must be 
switched off and secured against inadvertent operation. Please contact a Zeiss service agency or 

the Carl Zeiss Microscopy Service to repair the instrument. 

 

Dust and dirt may impair the instrument’s performance. The instrument must be effectively 

protected from such influences and covered with the dust cover when not in use. Always check 
whether the instrument is switched off before you cover it. Broad temperature fluctuations, 

direct sunlight and vibrations should be avoided. 

 

 

The instruments are not equipped with special devices to protect against corrosive, potentially 

infectious, toxic, radioactive or other substances that may be hazardous to health. All legal 
regulations must be observed when handling such substances, particularly the relevant national 

accident prevention regulations. 

Содержание Fluar Illuminator Z mot.























Отзывы: