background image

 

Set-up 

Fluar Illuminator Z mot. 

Connecting the Fluar Illuminator Z mot. 

Carl Zeiss 

 
 

 

05/2012 

435180-9060-701 

17 

Removal of the manual stop slider 

 

Insert the ball-head screwdriver (SW 3 mm) into 
the hole (Fig. 7/

2

) and push its indentation 

upwards into the groove.  

 

Remove the stop slider  with the ball-head 
screwdriver. 

 

Removal of the motorized stop slider 

 

Insert the ball-head screwdriver into the hole 
(Fig. 7/

1

) press against the spring element until 

the stop slider projects slightly.  

 

Remove the stop slider by hand. 

 

 

If the stop slider  is not required, remove the 
slotted cover and replace it with the blind cover. 

 

 

For special fluorescence applications (producing optical cross-sections through the specimen) 

the ApoTome.2 system can be coupled with the Fluar Illuminator Z mot. 
For this purpose the diaphragm shaft is provided with a special cover which permits mounting 

of the ApoTome.2 slider. This cover is supplied with the ApoTome.2 system if required. 

 
 
 

3.6

 

Connecting the Fluar Illuminator Z mot.  

Connecting to a microscope system with coarse/fine drive 

 

Connect the CAN-RJ45 socket on the reverse side of the Fluar Illuminator Z mot. to the mains outlet 

with a plug-in power unit. 

 
Connecting to microscope system with focusing motor or SYCOP 3 / EMS 3 

 

Connect the Fluar Illuminator Z mot. to an empty CAN socket on the rear side of the focusing motor 
using a 0.5 m CAN-RJ45 cable or to the EMS 3 controller using a 1.0 m CAN-RJ45 cable.  

 

 

Fig. 7 

Removing the stop slider 

 
 

Содержание Fluar Illuminator Z mot.























Отзывы: