background image

 

INTRODUCTION 

Carl Zeiss 

Notes on instrument safety 

Fluar Illuminator Z mot. 

 
 

 

435180-9060-701 

05/2012 

 

 

On microscopes with motorized focusing drive there is a 

risk of pinching fingers

 in the work 

area when lowering the body of the microscope. 

 

 

Before switching on check that the joystick on the SYCOP 3 is at the zero position and not 

swiveled out, and that the foot pedal is clear. 

 

Automatic travel can be interrupted by pressing the STOP button on the focusing drive or 

the STOP button on the SYCOP 3, moving the joystick on the SYCOP 3 up and down, 

turning the knurled wheel on the HIP or pressing the Memory 1 or 2 keys on the HIP. 

 

Do not reach into the possible travel path of the motorized table. There is a risk of pinching 
or injury to the fingers when the table is positioned by the control unit. 

 

 

Defective instruments are not to be disposed of as ordinary domestic waste. They should be 

disposed of in accordance with the relevant regulations. 

 

Samples should also be disposed of in compliance with the relevant legal requirements and 

internal operating procedures. 

 

The separate operating  manuals for the Axio Zoom.V16, HXP 200 C and SYCOP 3 (if used) 

must be observed and the general safety requirements complied with. 

 

Operating Manual Axio Zoom.V16:  

Order No. 435080-9030-701, English edition 

 

Operating Manual SYCOP 3:  

 

Order No. 435611-9010-701, English edition 

 

Operating Manual HXP 200 C 

 

 

 
 

 

Fig. 1 

Warning signs on the Axio Zoom.V16 microscope system with Fluar Illuminator Z mot. and 
HXP 200 C illuminator 

 

Содержание Fluar Illuminator Z mot.























Отзывы: