12 | 200
EN
(1)
(2)
(8)
(5)
(9)
(6)
(11)
(10)
(7)
Observation mode
Look through the viewfinder
(10)
to observe the scene. Turn the diopter adjustment
(11)
on the side to focus the screen.
Turn the focus ring
(1)
on the lens to focus on the scene.
Zoom
In observation mode, the arrow keys
(7)
can be used to zoom in (right arrow key) and
zoom out (left arrow key) the scene. Zoom in increments of 0.5 between 1.0x and 4.0x.
The zoom function is circular, i.e. if you press the right
arrow key
(7)
again after a 4.0x zoom, you will return
to 1.0x.
The currently set digital magnification is shown
on the display.
Color modes
The scene can be displayed in four different color modes. Briefly press the menu button
(8)
to change the observation mode.
When changed, the selected mode is shown on the display as text for about 2 seconds.
The following color modes can be selected:
• White Hot:
Cold areas are displayed here in black and warm areas in white.
•
Black Hot:
Cold areas are displayed here in white and warm areas in black.
•
Red Hot:
Cold areas are displayed here in black and warm areas in white.
In addition, the warmest areas are shown in yellow to red.
•
Rainbow:
a varied color palette displays cold areas in black to blue and warm areas
in yellow to white.
LED-Off
To switch off the LED on your ZEISS DTI 3, press the right arrow button
(7)
for
5 seconds. The LED then switches off. Repeat this procedure to switch on the LED
again.
Auto-Off
The ZEISS DTI 3 switches off automatically after 60 minutes of inactivity in order to save
battery power.
(1)
(2)
(12)
(13)
(14)
(10)
(11)
(15)
Power on/off
Press the on/off button
(5)
for a longer time to switch on the device.
The LED
(9)
is
green. The LED
(9)
lights up red when the charge level is low.
Press the on/off button
(5)
for a longer time to switch off the device again.
The LED
is off.
When switched on, the LED
(9)
lights up red when the charge level is low.
Note:
The on/off button
(5)
must be pressed
until the OFF symbol appears on the display. Only
then can the on/off button
(5)
be released and
the device switches off. If the on/off button
(5)
is
released before the OFF symbol is displayed, the
device does not switch off but switches to standby
mode.
Standby mode
Briefly press the on/off button
(5)
to switch
the device to standby mode. The LED
(9)
blinks
green. Briefly press the on/off button
(5)
again to switch the device back to observation
mode. The LED
(9)
is permanently green.
In standby mode, the LED
(9)
flashes red when the charge level is low.
Calibration
The device enables you to perform automatic (Auto Calibration = On) or manual
calibrations (Auto Calibration = Off).
In automatic mode, the device automatically performs a calibration by closing and
opening an internal shutter when necessary. A gentle click should be heard. In this
mode, you also have the option of performing the calibration manually by pressing
the Shutter button
(6)
and the Menu button
(8)
simultaneously.
There is a further option for performing a manual, silent calibration. Go to the device
menu and set the "Auto Calibration" option to "Off". Then return to the observation
mode. Close the lens cap manually. Now press the Shutter button
(6)
and the Menu
button
(8)
simultaneously. The device is now calibrated again.
Note:
Always cover the lens when performing a manual calibration. Otherwise
the sensor cannot calibrate correctly and the image will deteriorate, e.g. ghost images.
If you forget to cover the lens during a manual calibration, repeat the calibration
procedure with the lens covered.
2
X
