Zapi EPS-BLI HYG Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 75

background image

AFMNA0AA – EPS-BLI HYG – User Manual

Page – 67/75

12 INSTALLATION REQUIREMENTS &
RECOMMENDATIONS

1. TAKE CARE THE CONNECTOR COUNTERPARTS (HEADER PINS AND

RECEPTACLE CONTACTS) ARE CHEMICALLY HOMOGENEUS.

E-steering motor controller adopts a 23-poles Ampseal header tin plated
connector. So the contacts in the counterpart must be tin plated too. In case a
gold plated type Ampseal connector will be used in the E-steering motor
controller side, the contacts in the counterpart must be gold plated too.

2. DO NOT CONNECT A LIVE BATTERY TO THE E-STEERING MOTOR

CONTB and –B CONNECTIONS.

A live battery generates a conflict with the discharged caps rail inside the E-
steering motor controller: a consequent spark will damage (melt) the pins of the
connector.

Keep the battery unplugged when connecting the receptacle to

its header counterpart.

3. TAKE CARE YOUR FINGERS STAY AWAY FROM THE PINS OF THE E-

STEERING MOTOR CONTROLLER CONNECTOR DURING INSTALLATION.

Fingers can bend or contaminate the pins.

4. THE PINION IN THE MOTOR IS VERY SENSITIVE TO MECHANICAL

IMPACTS.

Impacts may cause the pinion-to-gear joint to become louder. Take care the
protection cap of the pinion is not removed before of the final installation. When
the cap has been removed be careful that the pinion does not impact any
metallic part during the installation.

«
...
65
66
67
68
69
...
»

Содержание EPS-BLI HYG












































































Отзывы:

Нет отзывов

Похожие инструкции для EPS-BLI HYG

Concord express

Бренд: GE Страницы: 3

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 10

Бренд: Baby Jogger Страницы: 16

Бренд: Febco Страницы: 12

Бренд: GameSir Страницы: 8

Бренд: Game ready Страницы: 21

Бренд: VAMP Страницы: 304

Бренд: Tactical Страницы: 8

Бренд: Raypak Страницы: 24

Бренд: J+J Страницы: 91

Бренд: Xantrex Страницы: 56

Бренд: Xantrex Страницы: 2

Freedom Sequence

Бренд: Xantrex Страницы: 58

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

Бренд: Full Gauge Controls Страницы: 3

Бренд: Vag Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды