Zapi EPS-BLI HYG Скачать руководство пользователя страница 44

Страница: 44 / 75

Page – 44/75

AFMNA0AA – EPS-BLI HYG – User Manual

9.2.7 TESTER

list

The TESTER list gives real time readouts of the state of the controller. It is possible to
know the state of digital I/Os (active or inactive), the voltage value of analog inputs
and the state of the main variables used in the motor.

Opening Zapi lines.

EPSHTM 6U NAx.xx

24 V 50 A 00000

Press ENTER to go into the main menu.

' % '

' ' '

The display will show: PARAMETER CHANGE.

MAIN MENU

PARAMETER CHANGE

Press ROLL UP or ROLL DOWN until TESTER
appears.

% ' '
% ' '

The display will show: TESTER.

MAIN MENU

TESTER

Press ENTER to go into the TESTER menu.

' % '
' ' '

The display will show the first readout.

SET POINT ONE

Press ROLL UP or ROLL DOWN to scroll the
readouts.

% ' '
% ' '

The display will show the desired readout and its
actual value.

MOTOR CURRENT

Press OUT to exit the menu.

' ' '

' % '

The display will show: TESTER.

CONFIG MENU

TESTER

Press OUT again. Display will show the opening
Zapi lines.

' ' '

' % '

1) SETPOINT

ANGLE

Unit: degrees.
Angle of the first set-point sensor.

2) SETPOINT

ANGLE

Unit: degrees.
Angle of the second set-point sensor.

3) SP DUTY CYCLE 1

Unit: percentage.
Duty cycle of the PWM from the first set-point sensor.

4) SP DUTY CYCLE 2

Unit: percentage.

Содержание EPS-BLI HYG












































































Результаты поиска

Содержание EPS-BLI HYG

Отзывы:

Похожие инструкции для EPS-BLI HYG

Бренды по названию

Популярные бренды

Zapi EPS-BLI HYG, Руководство пользователя

Результаты поиска

Содержание EPS-BLI HYG

Отзывы:

Похожие инструкции для EPS-BLI HYG

Бренды по названию

Популярные бренды