Zanotti Zero Series Скачать руководство пользователя

Страница: 7 / 78

Refrigeration unit

Series Zero Direct-Drive

Z200 | Z250 | Z350 | Z380

Z380 Multi

INSTALLATION MANUAL

rev.01

1 GENERAL INFORMATION

1.1 Introduction

NOTE

ZANOTTI S.p.A.

, the manufacturer of this refrigeration unit in question is referred to in

the manual as

Manufacturer

NOTE

The company that purchased the refrigeration unit is referred to in the manual as

Customer

This manual contains all the information necessary for correct installation and maintenance of the unit.

1.2 Symbols

The manual uses some symbols which are used to draw the reader’s attention and highlight some

particularly important aspects.

SYMBOL

MEANING

NOTES

DANGER

It indicates a risk of injury to the user. Pay close

attention to the text blocks indicated by this symbol.

CAUTION

It is a warning of possible deterioration or damage

to the refrigeration unit. Pay attention to the text

blocks indicated by this symbol.

WARNING

NOTE

It indicates a warning or a note on key functions or

useful information. Pay attention to the text blocks

indicated by this symbol.

Содержание Zero Series















































































Результаты поиска

Содержание Zero Series

Отзывы:

Похожие инструкции для Zero Series

Бренды по названию

Популярные бренды

Zanotti Zero Series, Руководство по установке

Результаты поиска

Содержание Zero Series

Отзывы:

Похожие инструкции для Zero Series

Бренды по названию

Популярные бренды