Zanotti Zero Series Скачать руководство пользователя

Страница: 54 / 78

INSTALLATION MANUAL

Refrigeration unit

Series Zero Direct-Drive

Z200 | Z250 | Z350 | Z380

Z380 Multi

rev.01

3.10 Electrical connections

NOTE

The Figure 62 shows an example of a standard wiring diagram. Please refer to the

specific wiring diagram of the version you are installing before proceeding with the

connections.

NOTE

The wires are marked with an identification number which is also shown on the wiring

diagram.

•

Connect the M8, M9, M10, and M11 fans (3, Figure 62) of the evaporators (depending on the

version).

•

Connect the BA cold room probe (9).

•

Connect the defrosting valve YS (6) - if supplied.

•

Connect the defrost termination thermostat FTS (8) - if supplied.

•

Connect the injection valve YI (5).

•

Connect the injection thermostat FTI (4) - if supplied.

•

Install the FSC fuse under key (7), as indicated in the paragraph 3.10.1.

•

Connect the red cable R to the FGS (1) battery protection fuse (positive pole)

•

Connect the other end of the FGS fuse to the battery positive pole.

Figure 61 - Battery protection fuse (positive pole)

•

Connect the black cable B (2) to the battery negative pole.

•

Connect the exhaust resistance ES (6), as indicated in paragraph 3.10.1- if present.

Содержание Zero Series















































































Результаты поиска

Содержание Zero Series

Отзывы:

Похожие инструкции для Zero Series

Бренды по названию

Популярные бренды

Zanotti Zero Series, Руководство по установке

Результаты поиска

Содержание Zero Series

Отзывы:

Похожие инструкции для Zero Series

Бренды по названию

Популярные бренды