Zanotti Zero Series Скачать руководство пользователя

Страница: 47 / 78

Refrigeration unit

Series Zero Direct-Drive

Z200 | Z250 | Z350 | Z380

Z380 Multi

INSTALLATION MANUAL

rev.01

•

Pass the pipes and the electrical connection cables to the evaporator through the hole on the

roof.

•

Fix the unit with the screws provided.

3.7 Evaporator installation

DANGER

The evaporator contains nitrogen under pressure. Before installation, release the

nitrogen as described in this paragraph.

To install the evaporator proceed as follows:

•

Allow the nitrogen to slowly escape from the suction, liquid, and defrosting lines by loosening the

caps.

•

Remove the evaporator panel to access the fastening holes.

•

Prepare the fastening holes according to the refrigeration unit model and the installation mode

(see. 2.1).

CAUTION

Position the evaporator respecting the distances indicated in the drawings in the chapter

2.1.

NOTE

Depending on the model and type of installation, the pipes and the electrical connection

cables can be routed alongside the evaporator or through the removable doors.

•

Fix the evaporator with the screws provided.

Содержание Zero Series















































































Результаты поиска

Содержание Zero Series

Отзывы:

Похожие инструкции для Zero Series

Бренды по названию

Популярные бренды

Zanotti Zero Series, Руководство по установке

Результаты поиска

Содержание Zero Series

Отзывы:

Похожие инструкции для Zero Series

Бренды по названию

Популярные бренды