DELETING MEMORY OF A RECEIVER
(restoring default settings)
SELECTIVE MEMORY DELETION OF RECEIVERS
After this operation, all push-buttons of transmitters added to a receiver’s memory are deleted.
Erasing (deleting) the memory includes the receiver is unpaired from the EXTA LIFE controller.
If the receiver’s memory included push-buttons assigned in time mode, then after memory dele-
tion the individually assigned push-buttons are also deleted. The zone time has a default setting
value - 10 seconds. If a user switched off deliberately pairing with the controller (see Switching
off pairing - Broadcast OFF), then deleting the receiver’s memory switches on automatically the
possibility of pairing (default setting).
In order to delete the whole memory of a receiver (restoring default settings), the following steps
must be carried out:
1. Press the PROG. push-button for about 5 seconds –STATUS LED switches on orange.
2. After STATUS LED switches off, release the PROG. push-button and in < 5 sec. press it again
shortly.
3. The STATUS LED flashes orange to signal the deleting is ongoing. The LED flashes orange
quickly to signal the operation has been completed successfully.
In the EXTA LIFE system receivers, there is a possibility to delete selectively push-buttons from
a receiver’s memory. It allows to delete selected buttons without deleting the whole memory of a
receiver. Push-buttons can be deleted directly (by means of the PROG. push-button) or remotely
by means of the EXTA LIFE application.
DIRECT DELETING OF PUSH-BUTTONS
BY MEANS OF PROG. PUSH-BUTTON
Selective deletion of push-buttons (or pairs for the switch on/switch off mode) from a receiver:
1. Press the PROG push-button for about 5 seconds –STATUS LED switches on orange.
2. After STATUS LED switches off, release the PROG. push-button and next within < 5 sec. press
shortly this push-button that will be deleted from the receiver’s memory. In case a pair of push-
buttons was assigned in a switch on/switch off mode, press only one of the buttons.
3. The STATUS LED flashes orange to signal the procedure of selective deleting has been com-
pleted.
REMOTE DELETION OF TRANSMITTER
BY MEANS OF EXTA LIFE APLICATION
In case we want to delete remotely transmitter’s push-buttons from a receiver, it is required that
the receiver is paired with the EXTA LIFE controller. To do the above, the following steps must
be carried out:
1. Choose the “Configure” option from the receiver’s (channel) menu (
).
2. Choose “Assigned transmitters” (
) in the configuration menu to display a current list of trans-
mitters added to its memory (
).
3. Press the transmitter’s name to display details included in its memory (numbers of added push-
buttons, operation modes, assigned time in time mode).
4. Choose the „Delete” option from the transmitter’s menu to delete selected push-buttons from a
receiver’s memory (
). A transmitter can also be deleted by sliding the element to the right or
left.
‘ZONE TIME’ PROGRAMMING
• Each new push-button assigned to ROP-21 in time mode operates with the so-called zone
time. The default zone time is adjusted to 10 seconds. A user can change the zone time value
in the range from 1 second to 18 hours. After time zone has been changed, the push-buttons
assigned to a receiver in time mode should automatically operate with the new value of the zone
time. The exception includes push-buttons with assigned individual times.
• Zone time value can be directly changed by means of a receiver and the PROG. push-button or
a mobile application, if the receiver is paired with the EXTA LIFE controller.
DIRECT PROGRAMMING OF ZONE TIME
(by means of the PROG. push-button)
1. Press the PROG push-button shortly (1sec). in a receiver –STATUS LED switches on blue.
2. Wait for about 5 seconds till the STATUS LED switches off.
3. After the LED is switched off, in < 5 sec. press shortly the PROG. push-button.
4. The STATUS LED starts flashing blue – it means time is measured.
5. After the time we want to assign as zone time, press shortly the PROG. push-button again.
6. The STATUS LED flashes orange to signal time has been programmed correctly.
REMOTE PROGRAMMING OF TIME ZONE
Remote zone time change for ROP-21 receiver is also possible by means of a mobile application.
To do it, pair the particular receiver with the EXTA LIFE system controller. Next, to adjust zone
time choose the “Configure” option from the receiver’s menu. Then, from the configuration screen
set basic parameters for the particular receiver (channel).
In case of zone time, it is required to adjust the “Zone Time” parameter in the range from 1 sec. to
18 hrs. in the following form: hours: minutes: seconds: (xxh : xxm : xxs).