Z Corporation ZPrinter 650 Скачать руководство пользователя страница 8

Страница: 8 / 68

09915

ZPrinter

650

Troubleshooting

Guide

3013: SEQUENCER: timed out finishing swath

..............................................................................

43000: SEQUENCER: missed position

............................................................................................

60300: REZERO: fast axis length out of tolerance

.........................................................................

60301: REZERO: Slow axis length out of tolerance

.......................................................................

Spread Issues: Problems with spreading powder efficiently

....................................................... 40

Spread not Smooth

..............................................................................................................................

Feeder is not dispensing enough powder (Short Spreading

Figure 21)

......................................

5001: POWDER: no more feed

..........................................................................................................

60100: Feeder timeout

........................................................................................................................

40204: TI: Build piston driver overload

.............................................................................................

Powder Handling: Issues with Depowering, Auto Gross De-powdering, Vacuum

...................... 46

Front/Rear Overflow is full or not emptying

......................................................................................

Build Bed will not empty

......................................................................................................................

No/Light Suction on User Hose

..........................................................................................................

De-powdering Chamber is full of powder while de-powdering

......................................................

No Compressed Air or not enough Compressed Air.

.....................................................................

Powder is seeping out of printer

........................................................................................................

Boot Failure and Inverter Issues: Printer will not come online

.................................................... 51

60200: LOWLEVEL: 15v supply voltage out of tolerance

..............................................................

61300: INVERTER: bad version number

..........................................................................................

61301: Timeout waiting for SPI bus

..................................................................................................

61302: INVERTER: comm error

........................................................................................................

61305: INVERTER: Heater driver over temp

...................................................................................

61308: INVERTER: Line under voltage

............................................................................................

Blank Illuminated LCD

.........................................................................................................................

Net Init Failed

........................................................................................................................................

Boot Failure: No Power

.......................................................................................................................

Communication and Software Errors: Errors that are caused by communication and software
problem

....................................................................................................................................... 55

Packet timeout: Printer not found: Before Printing

..........................................................................

Packet timeout: Printer not Found: While Printing

..........................................................................

1905: LAYERS: layer is too big

..........................................................................................................

Содержание ZPrinter 650





































































Результаты поиска

Содержание ZPrinter 650

Отзывы:

Z Corporation ZPrinter 650, Руководство по устранению неисправностей, Страница: 8 / 68

Результаты поиска

Содержание ZPrinter 650

Отзывы: