manualshive.com logo in svg

Z Corporation ZPrinter 650, Руководство по устранению неисправностей, Страница: 29 / 68

Поделиться
Скачать
Z Corporation ZPrinter 650 Скачать руководство пользователя страница 29

 

09915

 

ZPrinter

 

650

 

Troubleshooting

 

Guide

 

 

 2303(1): MOVER: axis 1 excessive position error 

This error is caused by the presence of or the appearance of excessive friction on the fast axis 
rails left to right.  

Monitor Read-Out or 

Secondary 

Symptom 

Cause / Problem 

Solution 

Reference 

Documents 

2303(1): MOVER: axis 1 

excessive position error 

Carriage is obstructed 

Remove obstruction 

  

2303(1): MOVER: axis 1 

excessive position error 

Rails, ends of travel and 

anti-rotates are dirty 

Clean rails, ends of travel 

and anti-rotates 

09577 ZPrinter650 User 

Manual 

(Figure 10 and 13) 

2303(1): MOVER: axis 1 

excessive position error 

Fast axis bearing needs oil 

Lubricate the fast axis 

bearing (reset the 

Maintenance in the 

software) 

09577 ZPrinter650 User 

Manual 

2303(1): MOVER: axis 1 

excessive position error 

Fast axis belt is loose/worn 

Retension the fast axis belt 

or Re-tension the fast axis 

belt or replace the 31503 

Tiamat Fast Axis Belt 

08861 ZPrinter650 Fast 

Axis Removal and 

Replacement Procedure 

2303(1): MOVER: axis 1 

excessive position error 

Fast Axis idler pulley is 

dirty/worn 

Clean Pulley with a dental 

Pick. If worn, replace the 

50038 Tiamat Fast Axis 

Idler Tensioner Ass'y 

(Figure 11 and 12)

  

2303(1): MOVER: axis 1 

excessive position error 

Fast axis motor pulley is 

dirty/worn 

Clean Pulley with a dental 

Pick. If worn, replace the 

31175 Pittman Motor 9234 

19.1V Modified, RoHS 

(Figure 11 and 12)

  

After performing the above steps try performing a service print head and alignment. If the machine performs both tasks 

then proceed with a test print. 

2303(1): MOVER: axis 1 

excessive position error 

Fast Axis Bearing failure 

Replace 06566 Fast Axis 

Assembly 

08861 ZPrinter650 Fast 

Axis Removal and 

Replacement Procedure 

2303(1): MOVER: axis 1 

excessive position error 

Bad slow axis motor 

Replace 31175 Fast Axis 

Motor  

After performing the above steps try performing a service print head and alignment. If the machine performs both tasks 

then proceed with a test print. 

2303(1): MOVER: axis 1 

excessive position error 

Add-On PCB Failed 

Replace 50017 Add-On 

PCB 

85070 ZPrinter 650 E-Box 

Field Repair Procedure 

2303(1): MOVER: axis 1 

excessive position error 

PC104+ Failed 

Replace 50016 PC104+ 

PCB 

85070 ZPrinter 650 E-Box 

Field Repair Procedure 

The main cause of this error is the buildup of powder and dirt on the axis rails and poor lubrication. 

 

 

29

 

 

Содержание ZPrinter 650





































































Отзывы:

Нет отзывов