manualshive.com logo in svg

YSI 3200, Руководство по эксплуатации

Поделиться
Скачать
YSI 3200 Скачать руководство пользователя страница 57

 

SECTION 9  WARRANTY AND REPAIR 

YSI Model 3200 Instruments are warranted for two years from date of purchase by the end 
user against defects in materials and workmanship. YSI cells and cables are warranted for 
one year from date of purchase by the end user against defects in material and workmanship.  
Within the warranty period, YSI will repair or replace, at its sole discretion, free of charge, 
any product that YSI determines to be covered by this warranty. 

To exercise this warranty, write or call your local YSI representative, or contact YSI 
Customer Service in Yellow Springs, Ohio. Send the product and proof of purchase, 
transportation prepaid, to the Authorized Service Center selected by YSI. Repair or 
replacement will be made and the product returned, transportation prepaid. Repaired or 
replaced products are warranted for the balance of the original warranty period, or at least 90 
days from date of repair or replacement. 

 

Limitation of Warranty 

This Warranty does not apply to any YSI product damage or failure caused by (i)  failure to install, 
operate or use the product in accordance with YSI’s written instructions, (ii) abuse or misuse of the 
product, (iii) failure to maintain the product in accordance with YSI’s written instructions or standard 
industry procedure, (iv) any improper repairs to the product, (v) use by you of defective or improper 
components or parts in servicing or repairing the product, or (vi) modification of the product in any 
way not expressly authorized by YSI. 

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR 
IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A 
PARTICULAR PURPOSE.  YSI’s LIABILITY UNDER THIS WARRANTY IS LIMITED TO 
REPAIR OR REPLACEMENT OF THE PRODUCT, AND THIS SHALL BE YOUR SOLE 
AND EXCLUSIVE REMEDY FOR ANY DEFECTIVE PRODUCT COVERED BY THIS 
WARRANTY.   IN NO EVENT SHALL YSI BE LIABLE FOR ANY SPECIAL, INDIRECT, 
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY DEFECTIVE 
PRODUCT COVERED BY THIS WARRANTY. 

YSI Incorporated 

Model 3200 

53

 

Содержание 3200























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды