York YVAG012 Скачать руководство пользователя страница 24

Страница: 24 / 56

FORM NO.:

6U5M-A11M-N

JOHNSON CONTROLS

to make any repair which may cause damage or electric

shock. For any maintenance demand, please contact the

manufacturer.

6. Never connect ground wire of unit power supply

with that of a gas fuel pipe, water pipe, lightning

arrester or telephone. Improper ground connection may

cause electric shock etc. Make sure connection between

ground wire and the ground terminal/the grounding

electrode is normal with regular inspection.

7. Field wiring should avoid edges of sheet metal,

sharp point of bolt, high-temperature tube pipe and

compressor shell in case of wire damage.

8. Wire fasteners should be used in case of wires

dropping out and wire damage caused by friction with

other parts.

9. Never touch with control elements and terminal

parts other than control panel in case of personal injury

as there’s electricity in control cabinet before power

supply is cutoff.

10. Never operate the wire controller with sharp

materials for fear of scratching the wire controller

screen. Never contort or pull out electric wires in the

control cabinet to prevent loose wiring and control

failure. Benzene, diluents or chemical reagent is not

allowed to clean the controller and control elements to

avoid corrosion or malfunction. Use cloth with neutral

decontaminant solution for cleaning during which the

cloth should not be too wet; then clean again with dry

cloth. Never excessively press on the screen in case of

allochromasia.

11. Electric wires and electronic wires should be

separated during unit wiring for normal communication

and operation.

ACCESSORY DIMENSIONS

FIGURE

– AUTO-SUPPLY VALVE DIMENSION

Notes:

All dimensions are in mm unless specified otherwise

FIGURE

– RELIEF VALVE DIMENSION

Notes:

All dimensions are in mm unless specified otherwise

Cooke Industries - Phone: +64 9 579 2185 Email: [email protected] Web: www.cookeindustries.co.nz

Содержание YVAG012

























































Результаты поиска

Содержание YVAG012

Отзывы:

Похожие инструкции для YVAG012

Бренды по названию

Популярные бренды

York YVAG012, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание YVAG012

Отзывы:

Похожие инструкции для YVAG012

Бренды по названию

Популярные бренды