York YVAG012 Скачать руководство пользователя страница 9

Страница: 9 / 56

FORM NO.:

6U5M-A11M-N

JOHNSON CONTROLS

SECTION 2 –INSTALLATION REQUIREMENTS

INSPECTION

Remove any transit packing and inspect the unit to

ensure that all components have been delivered and that

no damage has occurred during transit. If any damage

is evident, it should be noted on the carrier’s freight bill

and a claim entered in accordance with the instructions

given on the advice note.

Major damage must be reported immediately to your

local Johnson Controls representative.

MOVING THE UNIT

Prior to moving the unit, ensure that the installation site

is suitable for installing the unit and is easily capable of

supporting the weight of the unit and all associated

services.

The unit should be lifted using lifting lugs and a

spreader bar or frame of sufficient width to prevent

damage to the unit from the lifting chains.

The units shall be suitable for elevator or forklift truck

or crane for convenience of lifting. When transporting

with a crane, a canvas hammock shall be used to come

round the unit base and be fastened. If the packaging

box has been removed, in order to move the machine,

please apply suitable partition to protect the surface and

the side panel, as shown in the picture below. During

the transit, the machine shall be kept in level condition

to avoid damaging the unit due to crude operation.

Be particularly careful to ensure unit

steady. Pay special attention to the

weight distribution of the unit to avoid

maldistribution and the center of

gravity leans to the side of compressor.

Please try once before hoisting and

observe whether it is tightened and

whether there is any risk of tip-over of

the unit. The hoisting shall be slowly

lifted with constant speed to avoid the

tip-over of the unit and attention shall

be paid to the security of personnel

nearby.

Cooke Industries - Phone: +64 9 579 2185 Email: [email protected] Web: www.cookeindustries.co.nz

Содержание YVAG012

























































Результаты поиска

Содержание YVAG012

Отзывы:

Похожие инструкции для YVAG012

Бренды по названию

Популярные бренды

York YVAG012, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание YVAG012

Отзывы:

Похожие инструкции для YVAG012

Бренды по названию

Популярные бренды